Machine models

Hitachi ZX160LC-6 and ZX180LC-6 specifications

Which dash-6 brochure matches the excavator?

The ZX160LC-6 and ZX180LC-6 comparison needs an edition check before an equipment decision. Hitachi's November 2017 brochure describes HIOS III hydraulics for both. The January 2019 revision distinguishes HIOS IV on the 160 from HIOS III on the 180.

The model names stayed the same. A common dash number therefore does not establish identical hydraulic management on every machine advertised under it.

The earlier brochure describes an emissions arrangement using cooled exhaust-gas recirculation, an oxidation catalyst and selective catalytic reduction. No particulate filter is required for that arrangement. DEF is still present in its refill schedule; “no DPF” does not mean “no aftertreatment fluid.” The cab monitor offers programmed attachment operation and oil-flow adjustment.

Proportional fingertip attachment control was optional, so inspect the actual joystick before assuming a machine has it.

Sources: Hitachi DK160180HT, November 2017; January 2019 revision.

Arm length changes more than trench depth

The 160's shorter arm gives more arm crowd force; the longer arm extends reach and digging depth. Bucket force stays the same in the manufacturer's paired-arm schedule. Those are different tradeoffs.

Treating the whole table as one interchangeable digging envelope would promise the long arm's reach and the short arm's force together.

Transport height is also measured with the front attachment arranged for transport, not at the cab roof. The 180's longer arm has a higher overall transport envelope even though the cab itself has not changed height. Track shoe width then changes overall transport width.

Specify arm and shoes when requesting a haul measurement.

The 2019 weight schedules include fuel, an operator, bucket and counterweight. Their operating masses differ from the earlier brochure's entries, so both edition conditions remain visible. Neither schedule describes an empty machine with the attachment removed.

Main-pump delivery is listed per pump; hydraulic-tank refill is a volume. The earlier comparison had treated the tank's figure as a pump-flow rating.

Source: Hitachi 2019 technical, dimension and weight schedules.

Read the ZX180 lift chart across, then down

For the short-arm 180 on the specified shoes, the lift table separates forward lifting from lifting over the side. At the same height and radius the permissible load can differ. The chart also distinguishes hydraulic limits from stability limits.

Cable and hook weight belong in the lifted total. Select the column for the real lift direction and the row for the load point; digging force cannot substitute for a lifting rating.

Source: Hitachi ZX180LC-6 lift chart, page 21.

Entries in this reference
Listing-entry count
2

Short answer

Hitachi ZX160LC-6 and ZX180LC-6: full-size excavators.

Selected configuration figures
Configuration	Documented field and quantity
ZX160LC-6	Net Power 86 kW / 116 hp (manufacturer ISO 9249 pair) Hydraulic Pump Flow Capacity 191 L/min / 50 US gpm per main pump × 2
ZX180LC-6	Net Power 86 kW / 116 hp (manufacturer ISO 9249 pair) Hydraulic Pump Flow Capacity 191 L/min / 50 US gpm per main pump × 2

ZX160LC-6 and ZX180LC-6 specification matrix — Listing labels reported by the source
Publisher name	Source guide	Listing-entry count	Labels named by the source
Hitachi	ZX160LC-6 and ZX180LC-6	2	ZX160LC-6 and ZX180LC-6

Boom/Stick Option (Hex) 1
Specification	ZX160LC-6	ZX180LC-6
Max Cutting Height	8.88 m / 29 ft 2 in (2.60 m arm)	9.40 m / 30 ft 10 in (2.71 m arm)
Max Reach Along Ground	8.70 m / 28 ft 7 in (2.60 m arm)	9.27 m / 30 ft 5 in (2.71 m arm)
Max Vertical Wall Digging Depth	5.16 m / 16 ft 11 in (2.60 m arm)	5.55 m / 18 ft 3 in (2.71 m arm)
Max Digging Depth	5.98 m / 19 ft 7 in (2.60 m arm)	6.57 m / 21 ft 7 in (2.71 m arm)
Bucket Digging Force - ISO	25,180 lb	28,552 lb
Arm Digging Force - ISO	20,459 lb	21,358 lb
Arm Digging Force - SAE	19,784 lb	20,459 lb
Bucket Digging Force - SAE	22,257 lb	25,180 lb
Boom/Stick Option (Hex) 1	2.60 m (8 ft 6 in)	2.71 m (8 ft 10 in)
Minimum Swing Radius	2.91 m / 9 ft 7 in (2.60 m arm)	3.13 m / 10 ft 3 in
Max.Dumping Height	6.17 m / 20 ft 3 in (2.60 m arm)	6.57 m / 21 ft 7 in (2.71 m arm)

Dimensions and weight
Specification	ZX160LC-6
Ground Clearance	470 mm / 19 in
Tail Swing Radius	2.55 m / 8 ft 4 in (machine-dimension drawing)

Specification	ZX160LC-6	ZX180LC-6
Track Gauge	1.99 m / 6 ft 6 in	2.20 m / 7 ft 3 in
Counterweight Clearance	1030 mm / 3 ft 5 in	1030 mm / 3 ft 5 in
Overall Height	2.87 m / 9 ft 5 in with 2.60 m arm; 3.11 m / 10 ft 2 in with 3.10 m arm	3.08 m / 10 ft 1 in with 2.71 m arm; 3.39 m / 11 ft 1 in with 3.21 m arm
Overall Width	2.59 m / 8 ft 6 in with 600 mm shoes; 2.69 m / 8 ft 10 in with 700 mm shoes	2.80 / 2.90 / 3.00 m with 600 / 700 / 800 mm shoes
Overall Length	8.62 m / 28 ft 3 in with 2.60 m arm; 8.65 m / 28 ft 5 in with 3.10 m arm	9.04 m / 29 ft 8 in (both listed arms)
Cab Height	2.95 m / 9 ft 8 in	2.95 m / 9 ft 8 in
Center To Center – Idler To Sprocket	3.10 m / 10 ft 2 in	3.37 m / 11 ft 1 in
Undercarriage Overall Length	3.92 m / 12 ft 10 in	4.17 m / 13 ft 8 in

Undercarriage
Specification	ZX160LC-6	ZX180LC-6
Drawbar Pull	38,030 lb	17250 kg / 38030 lb (manufacturer force entry)
Number Of Carrier Rollers Per Side	2	2
Number Of Shoes Per Side	43	46
Number Of Track Rollers Per Side	7	7
Track Adjustment	Hydraulic	Hydraulic

Engine
Specification	ZX160LC-6	ZX180LC-6
Emission Tier Level	EPA Final Tier 4	EPA Final Tier 4
Battery	2	2
Number Of Cylinders	4	4
Off-Level Capacity	70 %	70 %
Engine Model	4JJ1	4JJ1
Net Power	86 kW / 116 hp (manufacturer ISO 9249 pair)	86 kW / 116 hp (manufacturer ISO 9249 pair)
Power Measured @	2200 rpm	2200 rpm
Displacement	183.1 cu in	183.1 cu in
Aspiration	Turbocharged and charged air cooled	Turbocharged and charged air cooled
Alternator	50 amps	50 amps

Operational
Specification	ZX160LC-6	ZX180LC-6
Swing Gearbox	6.9 L / 7.3 US qt	6.9 L / 7.3 US qt
Propel Gearbox (Each)	6.8 L / 7.2 US qt	6.8 L / 7.2 US qt
Operating Weight	38,400 lb	42,999 lb
Fuel Capacity	75.3 gal	75.3 gal
Cooling System Fluid Capacity	6.4 gal	6.4 gal
Hydraulic System Fluid Capacity	55.5 gal	58.2 gal
Engine Oil Capacity	4.5 gal	4.5 gal
Hydraulic Pump Flow Capacity	191 L/min / 50 US gpm per main pump × 2	191 L/min / 50 US gpm per main pump × 2

Performance
Specification	ZX160LC-6	ZX180LC-6
Travel Speed Low	km/h 3.4 mph 2.1	km/h 3.4 mph 2.1
Travel Speed - High	3.3 mph	3.3 mph

Swing Mechanism
Specification	ZX160LC-6	ZX180LC-6
Swing Speed	13.3 rpm	12.8 rpm
Swing Torque	44000 N·m (use metric column; brochure imperial conversion disagrees)	50000 N·m (use metric column; brochure imperial conversion disagrees)

Hydraulic System
Specification	ZX160LC-6	ZX180LC-6
Pilot Pump - Maximum Flow	8.9 gpm	8.9 gpm
Maximum Pressure Setting	570 psi	570 psi
Implement - Operating Pressure	4,980 psi	4,980 psi
Travel - Operating Pressure	4,980 psi	4,980 psi
Swing - Operating Pressure	4,980 psi	4,980 psi
Power Boost - Operating Pressure	5,511 psi	5,511 psi
Controls	Pilot levers, short-stroke, low-effort hydraulic pilot controls with shutoff lever	Pilot levers, short-stroke, low-effort hydraulic pilot controls with shutoff lever

Variants — Source comparison annotation
Source guide	Differing-field count reported
ZX160LC-6 and ZX180LC-6	26

Ratios
Figure	ZX160LC-6	ZX180LC-6
Engine horsepower per 1,000 lb of weight	3.0 (earlier reference weight)	2.7 (earlier reference weight)
Fuel tank per engine horsepower	0.65 US gal (116 hp brochure basis)	0.65 US gal (116 hp brochure basis)

ZX160LC-6 and ZX180LC-6: owner reports

Sources: 3 forum discussions about the Hitachi ZX160 excavators (ZX160LC-5N and earlier); heavyequipmentforums.com.

Hitachi: Injector codes after washing, hard starting and a final drive failure.

Sources: 3 forum discussions about the Hitachi ZX180 excavators (ZX180LC-5, -5N); heavyequipmentforums.com.

Hitachi: Attachment plumbing, codes and a high-hour purchase.

ZX160LC-6 and ZX180LC-6: forum references — Forum-title search
Forum index	Equipment class queried	Names in the search	Matching titles
Heavy Equipment Forums	full-size excavator	Hitachi and the ZX160LC, ZX180LC line that the ZX160LC-6, ZX180LC-6 belongs to (no title names the exact model)	17

Topics named by those titles
Title topic	Titles
hydraulics	2

Topic in the title	Threads	Share of matching threads
hydraulics	2	12%

Zx160 LC Weak Hydraulics With New Pump (Heavy Equipment Forums, 2026-05-29)
Zx160lc 2007 (Heavy Equipment Forums, 2025-11-26)
Hitachi Zx160lc (Heavy Equipment Forums, 2025-11-20)
Hitachi Zx160lc 2 Speed Travel Intermittent (Heavy Equipment Forums, 2025-09-09)

ZX160LC-6 and ZX180LC-6: dated market and recall observations — Dated listing search
Date	Listing index	Equipment class	Names queried	Result
2026-09-24	MachineryTrader (machinerytrader.com)	full-size excavator	ZX160LC-6, ZX180LC-6	No matching offers in this snapshot

Dated CPSC search
Date	Database	Names queried	Result
2026-09-24	U.S. Consumer Product Safety Commission	Hitachi; ZX160LC-6, ZX180LC-6	No matching recall in the stated search

Sources for this page
Evidence class	Document, classification and recorded date
Reference site	Reference site: Hitachi ZX160LC-6 — RitchieSpecs. Observed 2026-09-24.
Reference site	Reference site: Hitachi ZX180LC-6 — RitchieSpecs. Observed 2026-09-24.
Forum threads	Forum threads: Heavy Equipment Forums thread index for Hitachi ZX160LC-6 and ZX180LC-6 — Heavy Equipment Forums. Observed 2026-09-24.
Forum threads	Forum threads: Forum threads read for the Hitachi ZX160 excavators (ZX160LC-5N and earlier) — Heavyequipmentforums. Observed 2026-09-24.
Federal agency data	Federal agency data: Recall database search for Hitachi — U.S. Consumer Product Safety Commission. Observed 2026-09-24.

Earlier entries and manufacturer measurement corrections
Model and quantity	Earlier entry	Manufacturer quantity or condition
ZX160LC-6 Max Cutting Height	29.2 ft	8.88 m / 29 ft 2 in (2.60 m arm)
ZX180LC-6 Max Cutting Height	30.1 ft	9.40 m / 30 ft 10 in (2.71 m arm)
ZX160LC-6 Max Reach Along Ground	28.7 ft	8.70 m / 28 ft 7 in (2.60 m arm)
ZX180LC-6 Max Reach Along Ground	30.5 ft	9.27 m / 30 ft 5 in (2.71 m arm)
ZX160LC-6 Max Vertical Wall Digging Depth	16.11 ft	5.16 m / 16 ft 11 in (2.60 m arm)
ZX180LC-6 Max Vertical Wall Digging Depth	18.3 ft	5.55 m / 18 ft 3 in (2.71 m arm)
ZX160LC-6 Max Digging Depth	19.7 ft	5.98 m / 19 ft 7 in (2.60 m arm)
ZX180LC-6 Max Digging Depth	21.7 ft	6.57 m / 21 ft 7 in (2.71 m arm)
ZX160LC-6 Minimum Swing Radius	20.32 in	2.91 m / 9 ft 7 in (2.60 m arm)
ZX180LC-6 Minimum Swing Radius	12.33 in	3.13 m / 10 ft 3 in
ZX160LC-6 Max.Dumping Height	20.3 ft	6.17 m / 20 ft 3 in (2.60 m arm)
ZX180LC-6 Max.Dumping Height	21.7 ft	6.57 m / 21 ft 7 in (2.71 m arm)
ZX160LC-6 Ground Clearance	1.55 ft	470 mm / 19 in
ZX160LC-6 Tail Swing Radius	7.2 ft	2.55 m / 8 ft 4 in (machine-dimension drawing)
ZX160LC-6 Track Gauge	6.6 ft	1.99 m / 6 ft 6 in
ZX180LC-6 Track Gauge	7.3 ft	2.20 m / 7 ft 3 in
ZX160LC-6 Counterweight Clearance	3.38 ft	1030 mm / 3 ft 5 in
ZX180LC-6 Counterweight Clearance	3.38 ft	1030 mm / 3 ft 5 in
ZX160LC-6 Overall Height	10.2 ft	2.87 m / 9 ft 5 in with 2.60 m arm; 3.11 m / 10 ft 2 in with 3.10 m arm
ZX180LC-6 Overall Height	11.1 ft	3.08 m / 10 ft 1 in with 2.71 m arm; 3.39 m / 11 ft 1 in with 3.21 m arm
ZX160LC-6 Overall Width	10.6 in	2.59 m / 8 ft 6 in with 600 mm shoes; 2.69 m / 8 ft 10 in with 700 mm shoes
ZX180LC-6 Overall Width	11.82 in	2.80 / 2.90 / 3.00 m with 600 / 700 / 800 mm shoes
ZX160LC-6 Overall Length	28.5 ft	8.62 m / 28 ft 3 in with 2.60 m arm; 8.65 m / 28 ft 5 in with 3.10 m arm
ZX180LC-6 Overall Length	29.8 ft	9.04 m / 29 ft 8 in (both listed arms)
ZX160LC-6 Cab Height	11.62 in	2.95 m / 9 ft 8 in
ZX180LC-6 Cab Height	11.62 in	2.95 m / 9 ft 8 in
ZX160LC-6 Center To Center – Idler To Sprocket	10.2 ft	3.10 m / 10 ft 2 in
ZX180LC-6 Center To Center – Idler To Sprocket	11.1 ft	3.37 m / 11 ft 1 in
ZX160LC-6 Undercarriage Overall Length	8.2 ft	3.92 m / 12 ft 10 in
ZX180LC-6 Undercarriage Overall Length	13.8 ft	4.17 m / 13 ft 8 in
ZX180LC-6 Drawbar Pull	17,250 lb	17250 kg / 38030 lb (manufacturer force entry)
ZX160LC-6 Net Power	101 hp	86 kW / 116 hp (manufacturer ISO 9249 pair)
ZX180LC-6 Net Power	101 hp	86 kW / 116 hp (manufacturer ISO 9249 pair)
ZX160LC-6 Power Measured @	2,000 rpm	2200 rpm
ZX180LC-6 Power Measured @	2,200 rpm	2200 rpm
ZX160LC-6 Swing Gearbox	1.9 gal	6.9 L / 7.3 US qt
ZX180LC-6 Swing Gearbox	1.9 gal	6.9 L / 7.3 US qt
ZX160LC-6 Propel Gearbox (Each)	1.8 gal	6.8 L / 7.2 US qt
ZX180LC-6 Propel Gearbox (Each)	1.8 gal	6.8 L / 7.2 US qt
ZX160LC-6 Hydraulic Pump Flow Capacity	33.1 gpm	191 L/min / 50 US gpm per main pump × 2
ZX180LC-6 Hydraulic Pump Flow Capacity	33.1 gpm	191 L/min / 50 US gpm per main pump × 2
ZX160LC-6 Travel Speed Low	2.2 mph	km/h 3.4 mph 2.1
ZX180LC-6 Travel Speed Low	2.2 mph	km/h 3.4 mph 2.1
ZX160LC-6 Swing Torque	32,453 lb-ft	44000 N·m (use metric column; brochure imperial conversion disagrees)
ZX180LC-6 Swing Torque	36,878 lb-ft	50000 N·m (use metric column; brochure imperial conversion disagrees)
ZX160LC-6 Engine horsepower per 1,000 lb of weight	2.6	3.0 (earlier reference weight)
ZX180LC-6 Engine horsepower per 1,000 lb of weight	2.3	2.7 (earlier reference weight)
ZX160LC-6 Fuel tank per engine horsepower	0.75 gal	0.65 US gal (116 hp brochure basis)
ZX180LC-6 Fuel tank per engine horsepower	0.75 gal	0.65 US gal (116 hp brochure basis)

Source: Hitachi January 2019 schedules.

January 2019 equipped operating-weight schedule — separate from earlier reference
Model	Manufacturer weight pair as printed	Equipment condition
ZX160LC-6	kg 17717 lb 39024	Full fuel, 79 kg operator, 528 kg bucket, 3.10 m arm, 3210 kg counterweight, 700 mm shoes
ZX180LC-6	kg 20120 lb 44317	Full fuel, 79 kg operator, 600 kg bucket, 3.21 m arm, 3900 kg counterweight, 700 mm shoes

Source: Hitachi 2019 weight schedules, pages 13 and 19.

Hitachi ZX160LC-6 and ZX180LC-6: Configuration records

ZX160LC-6

Specification	Source figure
Boom/Stick Option (Hex) 1
Max Vertical Wall Digging Depth	5.16 m / 16 ft 11 in (2.60 m arm)
Boom/Stick Option (Hex) 1	2.60 m (8 ft 6 in)
Bucket Digging Force - ISO	25,180 lb
Arm Digging Force - ISO	20,459 lb
Arm Digging Force - SAE	19,784 lb
Bucket Digging Force - SAE	22,257 lb
Minimum Swing Radius	2.91 m / 9 ft 7 in (2.60 m arm)
Max.Dumping Height	6.17 m / 20 ft 3 in (2.60 m arm)
Dimensions and weight
Ground Clearance	470 mm / 19 in
Tail Swing Radius	2.55 m / 8 ft 4 in (machine-dimension drawing)
Counterweight Clearance	1030 mm / 3 ft 5 in
Overall Height	2.87 m / 9 ft 5 in with 2.60 m arm; 3.11 m / 10 ft 2 in with 3.10 m arm
Undercarriage
Number Of Track Rollers Per Side	7
Number Of Carrier Rollers Per Side	2
Number Of Shoes Per Side	43
Drawbar Pull	38,030 lb
Track Adjustment	Hydraulic
Engine
Number Of Cylinders	4
Engine Model	4JJ1
Net Power	86 kW / 116 hp (manufacturer ISO 9249 pair)
Power Measured @	2200 rpm
Aspiration	Turbocharged and charged air cooled
Displacement	183.1 cu in
Emission Tier Level	EPA Final Tier 4
Battery	2
Off-Level Capacity	70 %
Alternator	50 amps
Operational
Earlier Reference Operating Weight — Keep separate from January 2019 manufacturer equipped-weight schedule.	38,400 lb
Fuel Capacity	75.3 gal
Cooling System Fluid Capacity	6.4 gal
Hydraulic System Fluid Capacity	55.5 gal
Engine Oil Capacity	4.5 gal
Hydraulic Pump Flow Capacity	191 L/min / 50 US gpm per main pump × 2
Swing Gearbox	6.9 L / 7.3 US qt
Propel Gearbox (Each)	6.8 L / 7.2 US qt
Swing Mechanism
Swing Speed	13.3 rpm
Swing Torque	44000 N·m (use metric column; brochure imperial conversion disagrees)
Performance
Travel Speed Low	km/h 3.4 mph 2.1
Travel Speed - High	3.3 mph
Hydraulic System
Pilot Pump - Maximum Flow	8.9 gpm
Maximum Pressure Setting	570 psi
Implement - Operating Pressure	4,980 psi
Travel - Operating Pressure	4,980 psi
Swing - Operating Pressure	4,980 psi
Power Boost - Operating Pressure	5,511 psi
Controls	Pilot levers, short-stroke, low-effort hydraulic pilot controls with shutoff lever
Additional specifications
Max Cutting Height	8.88 m / 29 ft 2 in (2.60 m arm)
Max Reach Along Ground	8.70 m / 28 ft 7 in (2.60 m arm)
Max Digging Depth	5.98 m / 19 ft 7 in (2.60 m arm)
Track Gauge	1.99 m / 6 ft 6 in
Overall Length	8.62 m / 28 ft 3 in with 2.60 m arm; 8.65 m / 28 ft 5 in with 3.10 m arm
Cab Height	2.95 m / 9 ft 8 in
Center To Center – Idler To Sprocket	3.10 m / 10 ft 2 in
Undercarriage Overall Length	3.92 m / 12 ft 10 in

Source

ZX180LC-6

Specification	Source figure
Boom/Stick Option (Hex) 1
Max Vertical Wall Digging Depth	5.55 m / 18 ft 3 in (2.71 m arm)
Boom/Stick Option (Hex) 1	2.71 m (8 ft 10 in)
Bucket Digging Force - ISO	28,552 lb
Arm Digging Force - ISO	21,358 lb
Arm Digging Force - SAE	20,459 lb
Bucket Digging Force - SAE	25,180 lb
Minimum Swing Radius	3.13 m / 10 ft 3 in
Max.Dumping Height	6.57 m / 21 ft 7 in (2.71 m arm)
Dimensions and weight
Counterweight Clearance	1030 mm / 3 ft 5 in
Overall Height	3.08 m / 10 ft 1 in with 2.71 m arm; 3.39 m / 11 ft 1 in with 3.21 m arm
Undercarriage
Number Of Track Rollers Per Side	7
Number Of Carrier Rollers Per Side	2
Number Of Shoes Per Side	46
Drawbar Pull	17250 kg / 38030 lb (manufacturer force entry)
Track Adjustment	Hydraulic
Engine
Number Of Cylinders	4
Engine Model	4JJ1
Net Power	86 kW / 116 hp (manufacturer ISO 9249 pair)
Power Measured @	2200 rpm
Aspiration	Turbocharged and charged air cooled
Displacement	183.1 cu in
Emission Tier Level	EPA Final Tier 4
Battery	2
Off-Level Capacity	70 %
Alternator	50 amps
Operational
Earlier Reference Operating Weight — Keep separate from January 2019 manufacturer equipped-weight schedule.	42,999 lb
Fuel Capacity	75.3 gal
Cooling System Fluid Capacity	6.4 gal
Hydraulic System Fluid Capacity	58.2 gal
Engine Oil Capacity	4.5 gal
Hydraulic Pump Flow Capacity	191 L/min / 50 US gpm per main pump × 2
Swing Gearbox	6.9 L / 7.3 US qt
Propel Gearbox (Each)	6.8 L / 7.2 US qt
Swing Mechanism
Swing Speed	12.8 rpm
Swing Torque	50000 N·m (use metric column; brochure imperial conversion disagrees)
Performance
Travel Speed Low	km/h 3.4 mph 2.1
Travel Speed - High	3.3 mph
Hydraulic System
Pilot Pump - Maximum Flow	8.9 gpm
Maximum Pressure Setting	570 psi
Implement - Operating Pressure	4,980 psi
Travel - Operating Pressure	4,980 psi
Swing - Operating Pressure	4,980 psi
Power Boost - Operating Pressure	5,511 psi
Controls	Pilot levers, short-stroke, low-effort hydraulic pilot controls with shutoff lever
Additional specifications
Max Cutting Height	9.40 m / 30 ft 10 in (2.71 m arm)
Max Reach Along Ground	9.27 m / 30 ft 5 in (2.71 m arm)
Max Digging Depth	6.57 m / 21 ft 7 in (2.71 m arm)
Track Gauge	2.20 m / 7 ft 3 in
Overall Length	9.04 m / 29 ft 8 in (both listed arms)
Cab Height	2.95 m / 9 ft 8 in
Center To Center – Idler To Sprocket	3.37 m / 11 ft 1 in
Undercarriage Overall Length	4.17 m / 13 ft 8 in