Machine models
Dressta TD14M: STD, LT and LGP tracks, blades and steering
TD14M STD, LT and LGP use different track frames
In Dressta's October 2014 specification, STD has seven bottom rollers and a shorter ground-contact length. LT and LGP have eight rollers and longer tracks. LT retains the standard track gauge; LGP widens it and uses wider clipped-corner shoes.
A long-track machine is therefore not automatically the low-ground-pressure version.
Blade selection follows the undercarriage. The STD/LT columns offer Semi-U and six-way fronts. LGP has straight and six-way alternatives.
In particular, the LGP six-way blade is wider and has a different capacity from the STD/LT six-way blade. The brochure also separates hydraulic angle and tilt from manual pitch adjustment. Six-way does not mean hydraulically adjustable pitch.
Its two-speed steering module maintains drive to both tracks through gradual turns, while clutch-and-brake steering provides the tighter or pivoting maneuver. Coupling the steering ranges to the three-speed powershift produces six forward and six reverse travel combinations. Counting only the transmission ratios misses half that explanation.
Source: Dressta TD-14M MS-4022-DSS7, October 2014, chassis and blade tables.
The TD14M cylinder and refill depend on the arrangement
The hydraulic-cylinder listing separates the standard lift cylinder from the LT/LGP lift cylinder and from the six-way front. Their published strokes differ even where the bore matches. Order a cylinder or seal kit against the fitted front and its identity, rather than choosing it from the engine horsepower.
The blade drawing adds another distinction: maximum blade lift, blade drop and pitch adjustment have their own callouts. A blade-height figure cannot stand in for any of them.
Final-drive oil capacity changes with the wider undercarriage. Dressta specifies 28 liters per side for STD/LT and 46 liters per side for LGP. These are individual final-drive compartments.
The transmission system and hydraulic reservoir have separate refill entries, so treating the larger final-drive number as a whole-machine hydraulic refill would put it against the wrong compartment.
Enclosure also changes the weight column. The published six-way machines with full fuel have separate canopy and cab rows for each track frame. The cover uses canopy weights; the cab row is heavier.
Establish that condition before comparing a transport quotation or calculating ground pressure from an advertised mass.
Source: Dressta TD-14M original technical sheet, refill, cylinder and operating-weight conditions.
| Model and field | Earlier entry | Manufacturer figure and scope | Source |
|---|---|---|---|
| TD14M Number Of Track Rollers Per Side | 2 | 7 | Original document |
| TD14M Number Of Carrier Rollers Per Side | 7 | 2 | Original document |
| TD14M Pump Flow Capacity | 30.2 gpm | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed | Original document |
| TD14M LGP Number Of Track Rollers Per Side | 2 | 8 | Original document |
| TD14M LGP Number Of Carrier Rollers Per Side | 8 | 2 | Original document |
| TD14M LGP Pump Flow Capacity | 30.2 gpm | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed | Original document |
| TD14M LT Number Of Track Rollers Per Side | 2 | 8 | Original document |
| TD14M LT Number Of Carrier Rollers Per Side | 8 | 2 | Original document |
| TD14M LT Pump Flow Capacity | 30.2 gpm | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed | Original document |
| TD14M LGP Final Drives Fluid Capacity | 7.4 gal | 46 L (12 US gal) per side, LGP; STD/LT use 28 L (7.4 US gal) per side | Original document |
| Listing-entry count |
|---|
| 3 |
Short answer
Dressta TD14M: STD, LT and LGP tracks, blades and steering: crawler dozers.
| Publisher name | Source guide | Listing-entry count | Labels named by the source |
|---|---|---|---|
| Dressta | TD14M, TD14M LGP, and TD14M LT | 3 | TD14M, TD14M LGP, and TD14M LT |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Length W/ Blade | 17.46 ft | 18.18 ft | 18.18 ft |
| Width Over Tracks | 8.01 ft | 10.01 ft | 8.01 ft |
| Height To Top Of Cab | 10.63 ft | 10.63 ft | 10.63 ft |
| Length Of Track On Ground | 8.54 ft | 10.41 ft | 10.41 ft |
| Ground Clearance | 1.42 ft | 1.42 ft | 1.42 ft |
| Length W/O Blade | 11.91 ft | 13.78 ft | 13.78 ft |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Track Gauge | 6.17 ft | 7.03 ft | 6.17 ft |
| Standard Shoe Size | 22.05 in | 36.03 in | 22.05 in |
| Number Of Carrier Rollers Per Side | 2 | 2 | 2 |
| Ground Pressure | 8 psi | 4.6 psi | 6.9 psi |
| Ground Contact Area | 4,495 in2 | 8,990 in2 | 5,580 in2 |
| Number Of Shoes Per Side | 40 | 46 | 46 |
| Number Of Track Rollers Per Side | 7 | 8 | 8 |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Number Of Cylinders | 6 | 6 | 6 |
| Engine Model | QSB6.7 | QSB6.7 | QSB6.7 |
| Gross Power | 173 hp | 173 hp | 173 hp |
| Net Power | 160 hp | 160 hp | 160 hp |
| Power Measured @ | 1,800 rpm | 1,800 rpm | 1,800 rpm |
| Max Torque | 659 lb-ft | 659 lb-ft | 659 lb-ft |
| Displacement | 408 cu in | 408 cu in | 408 cu in |
| Torque Measured @ | 1,350 rpm | 1,350 rpm | 1,350 rpm |
| Aspiration | Turbocharged | Turbocharged | Turbocharged |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Operating Weight | 35,495 lb | 40,124 lb | 37,699 lb |
| Fuel Capacity | 100.4 gal | 100.4 gal | 100.4 gal |
| Cooling System Fluid Capacity | 9 gal | 9 gal | 9 gal |
| Engine Oil Capacity | 4.9 gal | 4.9 gal | 4.9 gal |
| Hydraulic Fluid Capacity | 15.6 gal | 15.6 gal | 15.6 gal |
| Powertrain Fluid Capacity | 33.1 gal | 33.1 gal | 33.1 gal |
| Final Drives Fluid Capacity | 7.4 gal | 46 L (12 US gal) per side, LGP; STD/LT use 28 L (7.4 US gal) per side | 7.4 gal |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Transmission Type | Powershift | Powershift | Powershift |
| Number Of Forward Gears | 3 | 3 | 3 |
| Number Of Reverse Gears | 3 | 3 | 3 |
| Max Speed - Forward | 6.8 mph | 6.8 mph | 6.8 mph |
| Max Speed - Reverse | 8.1 mph | 8.1 mph | 8.1 mph |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Relief Valve Pressure | 2,540 psi | 2,540 psi | 2,540 psi |
| Pump Flow Capacity | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Blade width | 10.7 ft | 12.8 ft | 10.7 ft |
| Blade height | 47.3 in | 46.1 in | 47.3 in |
| Capacity | 4.2 yd3 | 5 yd3 | 4.2 yd3 |
| Cutting Depth | 22.9 in | 21.2 in | 21.2 in |
| Source guide | Differing-field count reported |
|---|---|
| TD14M, TD14M LGP, and TD14M LT | 15 |
| Figure | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Engine horsepower per 1,000 lb of weight | 4.5 | 4.0 | 4.2 |
| Pump flow per engine horsepower | 0.19 gpm | 0.19 gpm | 0.19 gpm |
| Fuel tank per engine horsepower | 0.63 gal | 0.63 gal | 0.63 gal |
| Equipment group | crawler dozer |
|---|
| Forum index | Equipment class queried | Names in the search | Matching titles |
|---|---|---|---|
| Heavy Equipment Forums | crawler dozer | Dressta and the TD14M line that the TD14M, TD14M LGP, TD14M LT belongs to (no title names the exact model). That is too few titles to say what owners mostly ask about, so the most recent are listed instead | 3 |
- Dressta Td14m (Heavy Equipment Forums, 2024-04-06)
| Observation date | Listing source | Equipment search | Listings |
|---|---|---|---|
| 2026-09-24 | MachineryTrader | Dressta crawler dozer | 2 |
| Model | Listed | Model years | Lowest asking | Highest asking | Median asking | Median hours |
|---|---|---|---|---|---|---|
| TD14M | 1 | 2011 | $59,210 | $59,210 | $59,210 | None shown |
| TD14M LT | 1 | 2011 | $59,210 | $59,210 | $59,210 | None shown |
| Search date | Database | Names queried | Search result |
|---|---|---|---|
| 2026-09-24 | U.S. Consumer Product Safety Commission | Dressta together with the crawler dozer TD14M, TD14M LGP, TD14M LT | No matching recall in this search |
| Evidence class | Document, classification and recorded date |
|---|---|
| Reference site |
|
| Reference site |
|
| Reference site |
|
| Forum threads |
|
| Used-market listings |
|
| Federal agency data |
|
| Observation field | Recorded value |
|---|---|
| Title count | 3 |
| Forum indexes | Heavy Equipment Forums |
| Search wording | the TD14M, TD14M LGP, and TD14M LT crawler dozer |
| Latest title quoted by the reference | Dressta Td14m |
Dressta TD14M: STD, LT and LGP tracks, blades and steering: Configuration records
TD14M
| Specification | Source figure |
|---|---|
| Dimensions and weight | |
| Length W/ Blade | 17.46 ft |
| Width Over Tracks | 8.01 ft |
| Height To Top Of Cab | 10.63 ft |
| Length W/O Blade | 11.91 ft |
| Length Of Track On Ground | 8.54 ft |
| Ground Clearance | 1.42 ft |
| Undercarriage | |
| Standard Shoe Size | 22.05 in |
| Ground Pressure | 8 psi |
| Ground Contact Area | 4,495 in2 |
| Track Gauge | 6.17 ft |
| Number Of Shoes Per Side | 40 |
| Number Of Track Rollers Per Side | 7 [source] |
| Number Of Carrier Rollers Per Side | 2 [source] |
| Engine | |
| Number Of Cylinders | 6 |
| Engine Model | QSB6.7 |
| Gross Power | 173 hp |
| Power Measured @ | 1,800 rpm |
| Max Torque | 659 lb-ft |
| Displacement | 408 cu in |
| Torque Measured @ | 1,350 rpm |
| Net Power | 160 hp |
| Aspiration | Turbocharged |
| Operational | |
| Operating Weight | 35,495 lb |
| Fuel Capacity | 100.4 gal |
| Cooling System Fluid Capacity | 9 gal |
| Engine Oil Capacity | 4.9 gal |
| Hydraulic Fluid Capacity | 15.6 gal |
| Final Drives Fluid Capacity | 7.4 gal |
| Powertrain Fluid Capacity | 33.1 gal |
| Transmission and speeds | |
| Number Of Forward Gears | 3 |
| Number Of Reverse Gears | 3 |
| Max Speed - Forward | 6.8 mph |
| Max Speed - Reverse | 8.1 mph |
| Transmission Type | Powershift |
| Hydraulic System | |
| Relief Valve Pressure | 2,540 psi |
| Pump Flow Capacity | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed [source] |
| Standard Blade | |
| Blade width | 10.7 ft |
| Blade height | 47.3 in |
| Capacity | 4.2 yd3 |
| Cutting Depth | 22.9 in |
| Additional specifications | |
| Original Steering And Weight Conditions | MS-4022-DSS7 October 2014: three transmission ratios and two steering ranges provide six forward and six reverse combinations. Published canopy and cab weights include six-way blade and full fuel; they are separate rows. [source] |
| Cylinder And Blade Scope | STD lift cylinder 90 x 1100 mm; LT/LGP lift 90 x 930 mm; six-way front lift 90 x 1000 mm. STD/LT Semi-U 4.28 m3 versus six-way 3.20 m3; LGP straight 3.05 m3 versus six-way 3.80 m3. Six-way blade pitch is manual. [source] |
TD14M LGP
| Specification | Source figure |
|---|---|
| Dimensions and weight | |
| Length W/ Blade | 18.18 ft |
| Width Over Tracks | 10.01 ft |
| Height To Top Of Cab | 10.63 ft |
| Length W/O Blade | 13.78 ft |
| Length Of Track On Ground | 10.41 ft |
| Ground Clearance | 1.42 ft |
| Undercarriage | |
| Standard Shoe Size | 36.03 in |
| Ground Pressure | 4.6 psi |
| Ground Contact Area | 8,990 in2 |
| Track Gauge | 7.03 ft |
| Number Of Shoes Per Side | 46 |
| Number Of Track Rollers Per Side | 8 [source] |
| Number Of Carrier Rollers Per Side | 2 [source] |
| Engine | |
| Number Of Cylinders | 6 |
| Engine Model | QSB6.7 |
| Gross Power | 173 hp |
| Power Measured @ | 1,800 rpm |
| Max Torque | 659 lb-ft |
| Displacement | 408 cu in |
| Torque Measured @ | 1,350 rpm |
| Net Power | 160 hp |
| Aspiration | Turbocharged |
| Operational | |
| Operating Weight | 40,124 lb |
| Fuel Capacity | 100.4 gal |
| Cooling System Fluid Capacity | 9 gal |
| Engine Oil Capacity | 4.9 gal |
| Hydraulic Fluid Capacity | 15.6 gal |
| Final Drives Fluid Capacity | 46 L (12 US gal) per side, LGP; STD/LT use 28 L (7.4 US gal) per side [source] |
| Powertrain Fluid Capacity | 33.1 gal |
| Transmission and speeds | |
| Number Of Forward Gears | 3 |
| Number Of Reverse Gears | 3 |
| Max Speed - Forward | 6.8 mph |
| Max Speed - Reverse | 8.1 mph |
| Transmission Type | Powershift |
| Hydraulic System | |
| Relief Valve Pressure | 2,540 psi |
| Pump Flow Capacity | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed [source] |
| Standard Blade | |
| Blade width | 12.8 ft |
| Blade height | 46.1 in |
| Capacity | 5 yd3 |
| Cutting Depth | 21.2 in |
| Additional specifications | |
| Original Steering And Weight Conditions | MS-4022-DSS7 October 2014: three transmission ratios and two steering ranges provide six forward and six reverse combinations. Published canopy and cab weights include six-way blade and full fuel; they are separate rows. [source] |
TD14M LT
| Specification | Source figure |
|---|---|
| Dimensions and weight | |
| Length W/ Blade | 18.18 ft |
| Width Over Tracks | 8.01 ft |
| Height To Top Of Cab | 10.63 ft |
| Length W/O Blade | 13.78 ft |
| Length Of Track On Ground | 10.41 ft |
| Ground Clearance | 1.42 ft |
| Undercarriage | |
| Standard Shoe Size | 22.05 in |
| Ground Pressure | 6.9 psi |
| Ground Contact Area | 5,580 in2 |
| Track Gauge | 6.17 ft |
| Number Of Shoes Per Side | 46 |
| Number Of Track Rollers Per Side | 8 [source] |
| Number Of Carrier Rollers Per Side | 2 [source] |
| Engine | |
| Number Of Cylinders | 6 |
| Engine Model | QSB6.7 |
| Gross Power | 173 hp |
| Power Measured @ | 1,800 rpm |
| Max Torque | 659 lb-ft |
| Displacement | 408 cu in |
| Torque Measured @ | 1,350 rpm |
| Net Power | 160 hp |
| Aspiration | Turbocharged |
| Operational | |
| Operating Weight | 37,699 lb |
| Fuel Capacity | 100.4 gal |
| Cooling System Fluid Capacity | 9 gal |
| Engine Oil Capacity | 4.9 gal |
| Hydraulic Fluid Capacity | 15.6 gal |
| Final Drives Fluid Capacity | 7.4 gal |
| Powertrain Fluid Capacity | 33.1 gal |
| Transmission and speeds | |
| Number Of Forward Gears | 3 |
| Number Of Reverse Gears | 3 |
| Max Speed - Forward | 6.8 mph |
| Max Speed - Reverse | 8.1 mph |
| Transmission Type | Powershift |
| Hydraulic System | |
| Relief Valve Pressure | 2,540 psi |
| Pump Flow Capacity | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed [source] |
| Standard Blade | |
| Blade width | 10.7 ft |
| Blade height | 47.3 in |
| Capacity | 4.2 yd3 |
| Cutting Depth | 21.2 in |
| Additional specifications | |
| Original Steering And Weight Conditions | MS-4022-DSS7 October 2014: three transmission ratios and two steering ranges provide six forward and six reverse combinations. Published canopy and cab weights include six-way blade and full fuel; they are separate rows. [source] |
Compare Dressta TD14M, TD14M LGP, TD14M LT
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Length W/ Blade | 17.46 ft | 18.18 ft | 18.18 ft |
| Width Over Tracks | 8.01 ft | 10.01 ft | 8.01 ft |
| Height To Top Of Cab | 10.63 ft | 10.63 ft | 10.63 ft |
| Length Of Track On Ground | 8.54 ft | 10.41 ft | 10.41 ft |
| Ground Clearance | 1.42 ft | 1.42 ft | 1.42 ft |
| Length W/O Blade | 11.91 ft | 13.78 ft | 13.78 ft |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Track Gauge | 6.17 ft | 7.03 ft | 6.17 ft |
| Standard Shoe Size | 22.05 in | 36.03 in | 22.05 in |
| Number Of Carrier Rollers Per Side | 2 [source] | 2 [source] | 2 [source] |
| Ground Pressure | 8 psi | 4.6 psi | 6.9 psi |
| Ground Contact Area | 4,495 in2 | 8,990 in2 | 5,580 in2 |
| Number Of Shoes Per Side | 40 | 46 | 46 |
| Number Of Track Rollers Per Side | 7 [source] | 8 [source] | 8 [source] |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Number Of Cylinders | 6 | 6 | 6 |
| Engine Model | QSB6.7 | QSB6.7 | QSB6.7 |
| Gross Power | 173 hp | 173 hp | 173 hp |
| Net Power | 160 hp | 160 hp | 160 hp |
| Power Measured @ | 1,800 rpm | 1,800 rpm | 1,800 rpm |
| Max Torque | 659 lb-ft | 659 lb-ft | 659 lb-ft |
| Displacement | 408 cu in | 408 cu in | 408 cu in |
| Torque Measured @ | 1,350 rpm | 1,350 rpm | 1,350 rpm |
| Aspiration | Turbocharged | Turbocharged | Turbocharged |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Operating Weight | 35,495 lb | 40,124 lb | 37,699 lb |
| Fuel Capacity | 100.4 gal | 100.4 gal | 100.4 gal |
| Cooling System Fluid Capacity | 9 gal | 9 gal | 9 gal |
| Engine Oil Capacity | 4.9 gal | 4.9 gal | 4.9 gal |
| Hydraulic Fluid Capacity | 15.6 gal | 15.6 gal | 15.6 gal |
| Powertrain Fluid Capacity | 33.1 gal | 33.1 gal | 33.1 gal |
| Final Drives Fluid Capacity | 7.4 gal | 46 L (12 US gal) per side, LGP; STD/LT use 28 L (7.4 US gal) per side [source] | 7.4 gal |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Transmission Type | Powershift | Powershift | Powershift |
| Number Of Forward Gears | 3 | 3 | 3 |
| Number Of Reverse Gears | 3 | 3 | 3 |
| Max Speed - Forward | 6.8 mph | 6.8 mph | 6.8 mph |
| Max Speed - Reverse | 8.1 mph | 8.1 mph | 8.1 mph |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Relief Valve Pressure | 2,540 psi | 2,540 psi | 2,540 psi |
| Pump Flow Capacity | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed [source] | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed [source] | 135 L/min (35.7 US gpm), October 2014 tandem gear pump at rated engine speed [source] |
| Specification | TD14M | TD14M LGP | TD14M LT |
|---|---|---|---|
| Blade width | 10.7 ft | 12.8 ft | 10.7 ft |
| Blade height | 47.3 in | 46.1 in | 47.3 in |
| Capacity | 4.2 yd3 | 5 yd3 | 4.2 yd3 |
| Cutting Depth | 22.9 in | 21.2 in | 21.2 in |
More in Dressta: TD25M–TD40E, TD-9R–TD20M LT, TD7M–TD10R: M/R drives/track frames/engine differences.