Machine models
Cat 993: C32B engine ratings, lift and payload
Choose the 993 front and engine rating together
The C32B-powered 993 has separate high-regulation and lower-regulation engine schedules. Cat gives each schedule several power-test standards, so the largest horsepower number is not the same measurement as the net rating beside it. Specify both.
The original figures below remain separated by emissions arrangement; the unqualified bank entries have been identified as Tier 2 equivalent. A 993K comparison does not establish that its engine installation is interchangeable with this C32B machine.
High lift trades some rated payload for truck-loading geometry. The published standard-lift rating is in US tons as well as metric tonnes; the similarly labelled high-lift number is smaller in both units. Neither figure is a bucket volume.
Cat's selection method uses the combined bucket-and-material load: heavier bucket protection leaves less allowance for material. Density and fitted ground-engaging tools matter even when two buckets have the same nominal capacity.
Cat AEXQ3500-01, engine schedules and bucket-selection methodCat's feature sheet describes the truck match as a loading system: standard lift with a 777, high lift also reaching the 785 application. Its pass examples assume the matching truck and payload, not a guarantee for every quarry material. Choose the bucket for penetration as well as the truck bed.
The heavy-duty rock, high-abrasion rock and coal buckets serve different material conditions; extra protection has a performance cost.
Steering and gear selection share the STIC lever, while implement control has its own arrangement. The equipment list distinguishes the standard torque converter from the optional lock-up version. Direct-drive travel figures therefore need the matching hardware.
The published hydraulic cycle is a calculated high-lift cycle, not a measured complete truck-loading cycle including reversing and travel. For service planning, the technical sheet lists hydraulic tank contents separately from the whole factory-filled system. The old 993K fuel figure beside this page also belongs to that neighbour, not to the C32B loader's fuel tank.
Cat AEXQ3499, bucket applications, truck matching and equipment| Model and field | Earlier entry | Correction or scope | Source |
|---|---|---|---|
| 993 Rated Payload - High Lift | 27.5 t | 27.5 US tons (24.9 metric tonnes), high-lift arrangement | Original document |
| 993 Rated Payload - Standard Lift | 30 t | 30 US tons (27.2 metric tonnes), standard-lift arrangement | Original document |
| 993 Gross Power - SAE J1995 | 1,029 hp | 1,029 hp (767 kW), Tier2 equivalent; Tier4 schedule separately1,039hp775kW | Original document |
| 993 Net Power - ISO 14396 | 1,015 hp | 1,015 hp (757 kW), Tier2 equivalent; Tier4 schedule separately1,024hp764kW | Original document |
| 993 Net Power - ISO 9249 | 960 hp | 960 hp (716 kW), Tier2 equivalent; Tier4 schedule separately974hp726kW | Original document |
| 993 Net Power - SAE J1349 | 952 hp | 952 hp (710 kW), Tier2 equivalent; Tier4 schedule separately964hp719kW | Original document |
| 993 Net Power - EEC 80/1269 | 960 hp | 960 hp (716 kW), Tier2 equivalent; Tier4 schedule separately974hp726kW | Original document |
| 993 Operating Weight - Tier 2 Equivalent* | 294,687 lb | 294,687 lb (133,668 kg): high lift,50/65-51tires,standardcooling,13.8m3/18yd3bucket496-9912 | Original document |
| 993 Operating Weight - Tier 4 Final* | 294,687 lb | 294,687 lb (133,668 kg): high lift,50/65-51tires,standardcooling,13.8m3/18yd3bucket496-9912 | Original document |
| Listing-entry count |
|---|
| 1 |
Cat 993: C32B engine ratings, lift and payload: wheel loader.
| Configuration | Documented field and quantity |
|---|---|
| 993 |
| Specification | 993 |
|---|---|
| Engine Model | Cat C32B |
| Bore | 5.7 in |
| Displacement | 1,959 in³ |
| Emissions | US EPA Tier 4 Final, US EPA Tier 2 Equivalent |
| Gross Power - SAE J1995 | 1,039 hp |
| Net Power - EEC 80/1269 | 974 hp |
| Net Power - ISO 14396 | 1,024 hp |
| Net Power - ISO 9249 | 974 hp |
| Net Power - SAE J1349 | 964 hp |
| Peak Torque - 1,250 rpm | 4,034 lb/ft |
| Rated Speed | 1800 r/min |
| Stroke | 6.4 in |
| Torque Rise | 33% |
| Specification | 993 |
|---|---|
| Operating Weight - Tier 4 Final* | 294,687 lb (133,668 kg): high lift,50/65-51tires,standardcooling,13.8m3/18yd3bucket496-9912 |
| Bucket Range | 12.2-23.7 m3 (16.0-31 yd3) |
| Articulation Angle | 43 ° |
| Cat Truck Match - Standard Lift | 777 |
| Cat Truck Match - High Lift | 777, 785 |
| Operating Weight - Tier 2 Equivalent* | 294,687 lb (133,668 kg): high lift,50/65-51tires,standardcooling,13.8m3/18yd3bucket496-9912 |
| Rated Payload - High Lift | 27.5 US tons (24.9 metric tonnes), high-lift arrangement |
| Rated Payload - Standard Lift | 30 US tons (27.2 metric tonnes), standard-lift arrangement |
| Specification | 993 |
|---|---|
| Gross Power - SAE J1995 | 1,029 hp (767 kW), Tier2 equivalent; Tier4 schedule separately1,039hp775kW |
| Net Power - EEC 80/1269 | 960 hp (716 kW), Tier2 equivalent; Tier4 schedule separately974hp726kW |
| Net Power - ISO 14396 | 1,015 hp (757 kW), Tier2 equivalent; Tier4 schedule separately1,024hp764kW |
| Net Power - ISO 9249 | 960 hp (716 kW), Tier2 equivalent; Tier4 schedule separately974hp726kW |
| Net Power - SAE J1349 | 952 hp (710 kW), Tier2 equivalent; Tier4 schedule separately964hp719kW |
| Specification | 993 |
|---|---|
| Transmission Type | Cat Planetary Power Shift |
| Forward - 1 | 4.2 mph |
| Forward - 2 | 7.4 mph |
| Forward - 3 | 12.7 mph |
| Reverse - 1 | 4.7 mph |
| Reverse - 2 | 8.1 mph |
| Reverse - 3 | 13.9 mph |
| Direct Drive - Forward 1 | Lock-up disabled |
| Direct Drive - Forward 2 | 8 mph |
| Direct Drive - Forward 3 | 14.1 mph |
| Direct Drive - Reverse 1 | 4.9 mph |
| Direct Drive - Reverse 2 | 8.8 mph |
| Direct Drive - Reverse 3 | 15.6 mph |
| Specification | 993 |
|---|---|
| Cylinders - Lift/Tilt | Double-acting |
| Lift Cylinder - Bore | 10.5 in |
| Lift Cylinder - Stroke | 66.2 in |
| Lift/Tilt System - Circuit | Positive Flow Control |
| Lift/Tilt System - Pump | Variable Piston |
| Maximum Flow at 1,650 rpm | 311 gpm |
| Relief Valve Setting - Lift/Tilt | 4,200 psi |
| Tilt Cylinder - Bore | 9.3 in |
| Tilt Cylinder - Stroke | 40.9 in |
| Specification | 993 |
|---|---|
| Dump | 1.8 s |
| Lower | 3.8 s |
| Lower Float Down | 3.1 s |
| Rack Back | 2.4 s |
| Raise | 9.2 s |
| Total Hydraulic Cycle Time | 17.2 s |
The 993 beside its neighbours
| Base version | 993K | 993 |
|---|---|---|
| Engine power | 973 hp | 974 hp |
| Weight | 993K: 294,670 lb | |
| Fuel capacity | 993K: 545 gal | |
| Wheelbase | 993K: 19.33 ft | |
History and service record of 993
- One size up from the 992. The 993 sits one size class above the 992 in Caterpillar's large wheel loader range, sharing the same durability-through-multiple-lifecycles design philosophy Caterpillar applies across the whole large-loader line. Caterpillar, 993 Large Wheel Loader product page.
- Earlier and current large-loader references. The earlier ranking named the994K, described the995 as discontinued and cited the Guinness-listed LeTourneau L-2350 from a different manufacturer. Its discontinued wording is obsolete: Caterpillar now offers a new995 with the994K footprint and a higher rated payload. The earlier outside-manufacturer ranking remains attributed to Ritchie Bros., not a current Cat product specification.
| Forum index | Equipment class queried | Names in the search | Matching titles |
|---|---|---|---|
| Heavy Equipment Forums | wheel loader | Cat and the 993. That is too few titles to say what owners mostly ask about, so the most recent are listed instead | 1 |
- CAT Introduces The 993k (Heavy Equipment Forums, 2008-08-16)
| Observation date | Listing source | Equipment search | Listings |
|---|---|---|---|
| 2026-09-24 | MachineryTrader | Cat wheel loader | 15 |
| Model | Listed | Model years | Lowest asking | Highest asking | Median asking | Median hours |
|---|---|---|---|---|---|---|
| 993 | 15 | 2008 to 2019 | $232,285 | $1,150,000 | $306,501 | 736 |
| Search date | Database | Names queried | Search result |
|---|---|---|---|
| 2026-09-24 | U.S. Consumer Product Safety Commission | Cat together with the wheel loader 993 | No matching recall in this search |
| Evidence class | Document, classification and recorded date |
|---|---|
| Manufacturer |
|
| Forum threads |
|
| Published history |
|
| Published history |
|
| Used-market listings |
|
| Federal agency data |
|
Cat 993: C32B engine ratings, lift and payload: Configuration records
993
| Specification | Source figure |
|---|---|
| Operating Specifications | |
| Articulation Angle | 43 ° |
| Rated Payload - High Lift | 27.5 US tons (24.9 metric tonnes), high-lift arrangement [source] |
| Cat Truck Match - High Lift | 777, 785 |
| Rated Payload - Standard Lift | 30 US tons (27.2 metric tonnes), standard-lift arrangement [source] |
| Operating Weight - Tier 2 Equivalent* | 294,687 lb (133,668 kg): high lift,50/65-51tires,standardcooling,13.8m3/18yd3bucket496-9912 [source] |
| Operating Weight - Tier 4 Final* | 294,687 lb (133,668 kg): high lift,50/65-51tires,standardcooling,13.8m3/18yd3bucket496-9912 [source] |
| Bucket Range | 12.2-23.7 m3 (16.0-31 yd3) |
| Cat Truck Match - Standard Lift | 777 |
| Transmission and speeds | |
| Transmission Type | Cat Planetary Power Shift |
| Forward - 1 | 4.2 mph |
| Forward - 2 | 7.4 mph |
| Forward - 3 | 12.7 mph |
| Reverse - 1 | 4.7 mph |
| Reverse - 2 | 8.1 mph |
| Reverse - 3 | 13.9 mph |
| Direct Drive - Forward 1 | Lock-up disabled |
| Direct Drive - Forward 2 | 8 mph |
| Direct Drive - Forward 3 | 14.1 mph |
| Direct Drive - Reverse 1 | 4.9 mph |
| Direct Drive - Reverse 2 | 8.8 mph |
| Direct Drive - Reverse 3 | 15.6 mph |
| Hydraulic System Lift/Tilt | |
| Lift/Tilt System - Circuit | Positive Flow Control |
| Relief Valve Setting - Lift/Tilt | 4,200 psi |
| Lift/Tilt System - Pump | Variable Piston |
| Tilt Cylinder - Stroke | 40.9 in |
| Lift Cylinder - Bore | 10.5 in |
| Lift Cylinder - Stroke | 66.2 in |
| Tilt Cylinder - Bore | 9.3 in |
| Cylinders - Lift/Tilt | Double-acting |
| Maximum Flow at 1,650 rpm | 311 gpm |
| Hydraulic Cycle Times | |
| Raise | 9.2 s |
| Dump | 1.8 s |
| Total Hydraulic Cycle Time | 17.2 s |
| Rack Back | 2.4 s |
| Lower | 3.8 s |
| Lower Float Down | 3.1 s |
| Dimensions and weight | |
| Wheelbase | 5,890 mm (19.3 ft), both standard and high lift in AEXQ3500-01 [source] |
| Operational | |
| Fuel Capacity | 2,045 L (540.2 US gal), AEXQ3500-01 complete-fill schedule [source] |
| Additional specifications | |
| Gross Power - SAE J1995 | 1,029 hp (767 kW), Tier2 equivalent; Tier4 schedule separately1,039hp775kW [source] |
| Net Power - ISO 14396 | 1,015 hp (757 kW), Tier2 equivalent; Tier4 schedule separately1,024hp764kW [source] |
| Net Power - ISO 9249 | 960 hp (716 kW), Tier2 equivalent; Tier4 schedule separately974hp726kW [source] |
| Net Power - SAE J1349 | 952 hp (710 kW), Tier2 equivalent; Tier4 schedule separately964hp719kW [source] |
| Net Power - EEC 80/1269 | 960 hp (716 kW), Tier2 equivalent; Tier4 schedule separately974hp726kW [source] |
| Engine Model | Cat C32B |
| Emissions | US EPA Tier 4 Final, US EPA Tier 2 Equivalent |
| Rated Speed | 1800 r/min |
| Bore | 5.7 in |
| Stroke | 6.4 in |
| Displacement | 1,959 in³ |
| Torque Rise | 33% |
| Peak Torque - 1,250 rpm | 4,034 lb/ft |
| Hydraulic Tank | 553 L (146 US gal), tank only; factory system873L230USgal [source] |
| Tier 4 Gross Power SAE J1995 | 1,039 hp (775 kW), at1800rpm [source] |
| Tier 4 Net Power ISO 14396 | 1,024 hp (764 kW), at1800rpm [source] |
| Tier 4 Net Power ISO 9249 | 974 hp (726 kW), at1800rpm [source] |
| Tier 4 Net Power EEC 80/1269 | 974 hp (726 kW), at1800rpm [source] |
| Tier 4 Net Power SAE J1349 | 964 hp (719 kW), at1800rpm [source] |
More in Cat: 994D/994F, 993K: converter controls/hydraulic compartments, 995.