FieldSpec
Equipment menu

Machine models

John Deere 950C to 1050J Waste Handler: guarding, cooling and blade configurations

The J-Series waste package adds protection beyond a trash rack

Deere's dedicated 950J/1050J Waste Handler brochure describes a cab-to-frame barrier, guarded hose routing, perforated engine shields and protection around cooling components. Its track equipment uses cutouts and recessed sprocket details to discourage packed refuse. A blade rack by itself does not establish that a used dozer retains this package.

The brochure makes front and rear striker bars optional. Look for the actual installed bars and their condition before treating every illustrated guard as standard equipment. The engine and alternator air-cleaning arrangements are separate from the optional powered cab-air precleaner.

One visible roof-mounted cleaner does not describe all of those intake paths.

Source: original Deere 950J/1050J Waste Handler brochure, guarding and air-cleaning sections.

The seal warning concerns an outer oil-filled protection chamber

Deere describes bolt-on final-drive seal guards followed by an oil-filled double-seal arrangement. If debris compromises the outer seal, loss of oil from that protection arrangement triggers a cab warning; the inner seal retains oil in the final drive. The warning consequently identifies a protection failure that needs attention, not proof that the drive's inner chamber has already emptied.

Its service description also separates final-drive checks from the hydraulic/transmission reservoir. Find the indicated compartment before interpreting an oil-level complaint. The brochure provides dedicated sampling and diagnostic ports and a built-in cab-tilt arrangement for drivetrain access.

Follow the machine's service procedure when using that access; the sales illustration does not supply the supporting and locking sequence.

Waste cooling and standard cooling are different equipment scopes

The dedicated waste brochure describes side-by-side engine radiator and charge-air cooler cores, separate hydraulic/hydrostatic cooling and reversing fans. Its perforated hood and side shields form another debris barrier. Cleaning only the face of one cooler leaves the other named airflow paths unexamined.

The February2014 general J-Series brochure instead lists reversing fan drives as available equipment. It also lists waste handling as a package choice alongside woodchip and coal packages. Apply the dedicated waste-handler description only after confirming the machine's installed arrangement.

The shared J designation does not make every general-purpose dozer a waste handler.

Source: Deere DKA9501050J, February2014, cooling and equipment lists.

Blade capacity depends on whether the rack is included

The waste brochure separates its semi-U blade figures with and without the trash rack. It also distinguishes the blade itself from push beams, tilt cylinders and power-pitch equipment. Comparing the larger rack-equipped capacity with the smaller bare-blade weight would combine different assemblies.

Operating weight includes another set of conditions: waste equipment, specified track shoes and the rack-equipped blade. Shipping weight excludes blade and attachments and uses a partial fuel load. Neither number replaces the other when arranging transport.

Deere's 2008 fleet booklet also separates waste-handler dozers from its general crawler-dozer section; keep that distinction when comparing older C-Series entries with the J machines.

Sources: dedicated Waste Handler specification notes; original Deere Fleet2008 brochure.
Earlier reference entries and original manufacturer corrections
Model and fieldEarlier entryManufacturer figure and scopeSource
1050J Displacement733 cu in12.0 L (732 cu in), D946-L A6; original February2014 DKA9501050JOriginal document
1050J Waste Handler Displacement733 cu in12.0 L (732 cu in), D946-L A6; dedicated Deere Waste Handler brochureOriginal document
1050J Relief Valve Pressure3,700 psi26,000 kPa (3,770 psi), February2014 GENERAL1050J brochure; earlier dedicated waste-handler brochure prints3,700psi withsame26,000kPa, different publication entry retainedOriginal document
Entries in this reference
Listing-entry count
7
Short answer

John Deere 950C to 1050J Waste Handler: guarding, cooling and blade configurations: crawler dozers.

Selected configuration figures
ConfigurationDocumented field and quantity
950C
Net Power
230 hp
Operating Weight
50,600 lb
950C LGP
Net Power
230 hp
Operating Weight
54,200 lb
950C LT
Net Power
230 hp
Operating Weight
52,300 lb
1050C
Net Power
324 hp
Operating Weight
73,985 lb
1050C WH
Net Power
324 hp
Operating Weight
77,445 lb
1050J
Net Power
335 hp
Operating Weight
77,843 lb
1050J Waste Handler
Net Power
335 hp
Operating Weight
80,967 lb
950C to 1050J Waste Handler specification matrix — Listing labels reported by the source
Publisher nameSource guideListing-entry countLabels named by the source
John Deere950C to 1050J Waste Handler7950C, 950C LGP, 950C LT, 1050C, 1050C WH, 1050J, and 1 more
Dimensions and weight
Specification950C950C LGP1050C1050J1050J Waste Handler
Length W/ Blade18.64 ft18.94 ft21.05 ft21.33 ft21.33 ft
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Width Over Tracks8.17 ft9.51 ft9.76 ft8.99 ft10.32 ft9.17 ft9.17 ft
Height To Top Of Cab10.85 ft10.85 ft10.85 ft11.95 ft11.95 ft11.91 ft11.91 ft
Length Of Track On Ground9.72 ft10.75 ft10.75 ft10.42 ft10.42 ft10.42 ft10.42 ft
Ground Clearance1.59 ft1.59 ft1.59 ft2.06 ft2.06 ft2.08 ft2.08 ft
Specification950C950C LGP950C LT1050C1050C WH
Length W/O Blade14.11 ft14.11 ft14.11 ft16.03 ft16.03 ft
Undercarriage
Specification950C950C LGP950C LT1050C1050J1050J Waste Handler
Track Gauge6.5 ft7.16 ft6.5 ft7.16 ft7.17 ft7.17 ft
Specification950C950C LGP1050C1050J1050J Waste Handler
Standard Shoe Size20 in27.96 in22.05 in24 in24 in
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Number Of Shoes Per Side39434344444444
Ground Pressure10.81 psi7.42 psi10.1 psi13.4 psi12.9 psi12.9 psi13.8 psi
Ground Contact Area4,680 in27,224 in25,160 in25,510 in26,000 in26,004 in26,004 in2
Number Of Track Rollers Per Side7887777
Track Pitch8.5 in8.5 in8.5 in8.5 in8.5 in8.5 in8.5 in
Engine
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Number Of Cylinders6666666
Engine ModelD926 TID 926 TID 926 TID 9406 TI-ED 9406 TI-E A3D 946-L A6D 946-L A6
Net Power230 hp230 hp230 hp324 hp324 hp335 hp335 hp
Power Measured @1,800 rpm1,800 rpm1,800 rpm1,800 rpm1,800 rpm1,800 rpm1,800 rpm
Max Torque797 lb-ft797 lb-ft797 lb-ft1,129 lb-ft1,129 lb-ft1,254 lb-ft1,254 lb-ft
Displacement610 cu in610 cu in610 cu in793 cu in793 cu in12.0 L (732 cu in), D946-L A6; original February2014 DKA9501050J12.0 L (732 cu in), D946-L A6; dedicated Deere Waste Handler brochure
Torque Measured @1,300 rpm1,300 rpm1,300 rpm1,200 rpm1,200 rpm1,400 rpm1,400 rpm
AspirationIntercooled and turbochargedIntercooled and turbochargedIntercooled and turbochargedIntercooled and turbochargedIntercooled and turbochargedTurbocharger w/ intercoolerTurbocharger w/ intercooler
Operational
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Operating Weight50,600 lb54,200 lb52,300 lb73,985 lb77,445 lb77,843 lb80,967 lb
Fuel Capacity119 gal119 gal119 gal161 gal161 gal172 gal171.7 gal
Cooling System Fluid Capacity17.6 gal17.6 gal17.6 gal18 gal18 gal15 gal15.1 gal
Engine Oil Capacity6.7 gal6.7 gal6.7 gal6.3 gal6.3 gal9 gal9 gal
Hydraulic Fluid Capacity47 gal47 gal47 gal55 gal55 gal55.5 gal55.5 gal
Powertrain Fluid Capacity47 gal47 gal47 gal55 gal55 gal55.5 gal55.5 gal
Final Drives Fluid Capacity3.8 gal3.8 gal3.8 gal5.5 gal5.5 gal4.9 gal4.9 gal
Operating Voltage24 V24 V24 V24 V24 V24 V24 V
Alternator Supplied Amperage55 amps55 amps55 amps55 amps80 amps80 amps80 amps
Transmission and speeds
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Transmission TypeDual-path, electronic-controlled, closed-loop hydrostatic driveDual-path, electronic-controlled, closed-loop hydrostatic driveDual-path, electronic-controlled, closed-loop hydrostatic driveDual-path, electronic-controlled, closed-loop hydrostatic driveDual-path, electronic-controlled, closed-loop hydrostatic driveHydrostaticHydrostatic
Max Speed - Forward6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph
Max Speed - Reverse6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph
Specification950C950C LGP950C LT1050C1050C WH
Number Of Forward Gears33333
Number Of Reverse Gears33333
Hydraulic System
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Pump TypeVariable-displacement piston pump with load-sensing proportional pump flow controlVariable-displacement piston pump with load-sensing proportional pump flow controlVariable-displacement piston pump with load-sensing proportional pump flowVariable-displacement piston pump with load-sensing proportional pum flow controlVariable-displacement piston pump with load-sensing proprotional pump flow controlVariable axial-pistonVariable axial-piston
Relief Valve Pressure2,320 psi2,320 psi2,320 psi2,900 psi2,900 psi26,000 kPa (3,770 psi), February2014 GENERAL1050J brochure; earlier dedicated waste-handler brochure prints3,700psi withsame26,000kPa, different publication entry retained3,700 psi
Pump Flow Capacity77 gpm77 gpm77 gpm89 gpm89 gpm68 gpm68 gpm
Standard Blade
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Blade width13.1 ft14.8 ft13.1 ft13.8 ft13.8 ft13.3 ft13.3 ft
Blade height57 in53 in57 in65 in96.5 in65 in94 in
Capacity9.5 yd38.2 yd39.5 yd312.5 yd327.7 yd311.6 yd325.8 yd3
Cutting Depth21 in24 in21 in22 in22 in22 in22 in
Specification950C950C LGP950C LT1050C WH
Blade Angle (Both Directions)25 degrees25 degrees25 degrees25 degrees
Variants — Source comparison annotation
Source guideDiffering-field count reported
950C to 1050J Waste Handler37
Ratios
Figure950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Engine horsepower per 1,000 lb of weight4.54.24.44.44.24.34.1
Pump flow per engine horsepower0.33 gpm0.33 gpm0.33 gpm0.27 gpm0.27 gpm0.20 gpm0.20 gpm
Fuel tank per engine horsepower0.52 gal0.52 gal0.52 gal0.50 gal0.50 gal0.51 gal0.51 gal

950C to 1050J Waste Handler: owner reports

Sources: 3 forum discussions about the John Deere 950 compact tractors; tractorbynet.com.Sources: 3 forum discussions about the John Deere 1050 compact tractors (Yanmar-built); tractorbynet.com.

950C to 1050J Waste Handler: forum references

Related discussion: “New To Me 4wd JD 950 Steering Knuckle Leak Help”: 950.

Used market for the 950C to 1050J Waste Handler — Dated first-page listing snapshot
Observation dateListing sourceEquipment searchListings
2026-09-24MachineryTraderJohn Deere crawler dozer6
ModelListedModel yearsLowest askingHighest askingMedian askingMedian hours
950C12003None shownNone shownNone shownNone shown
1050C12006$65,000$65,000$65,000None shown
1050C WH12006$65,000$65,000$65,000None shown
1050J32010 to 2013$60,000$69,500$60,0009,700
950C to 1050J Waste Handler: recall reference — Dated CPSC search
Search dateDatabaseNames queriedSearch result
2026-09-24U.S. Consumer Product Safety CommissionJohn Deere together with the crawler dozer 950C, 950C LGP, 950C LT, 1050CNo matching recall in this search

Sources for this page

Evidence classDocument, classification and recorded date
Reference site
Reference site
Reference site
Reference site
Reference site
Reference site
Reference site
Forum threads
Used-market listings
Federal agency data
Recorded observations — Forum-title snapshot
Observation fieldRecorded value
Title count473
Forum indexesTractorByNet
Search wordingthe 950C to 1050J Waste Handler crawler dozer
Topics in the title resultshydraulics, starting and cranking, brakes and steering
Latest title quoted by the referenceNew To Me 4wd JD 950 Steering Knuckle Leak Help

John Deere 950C to 1050J Waste Handler: guarding, cooling and blade configurations: Configuration records

950C
SpecificationSource figure
Dimensions and weight
Width Over Tracks8.17 ft
Height To Top Of Cab10.85 ft
Length W/ Blade18.64 ft
Length Of Track On Ground9.72 ft
Ground Clearance1.59 ft
Length W/O Blade14.11 ft
Undercarriage
Track Gauge6.5 ft
Ground Contact Area4,680 in2
Ground Pressure10.81 psi
Standard Shoe Size20 in
Number Of Shoes Per Side39
Number Of Track Rollers Per Side7
Track Pitch8.5 in
Engine
Number Of Cylinders6
Engine ModelD926 TI
Net Power230 hp
Power Measured @1,800 rpm
Max Torque797 lb-ft
Displacement610 cu in
Torque Measured @1,300 rpm
AspirationIntercooled and turbocharged
Operational
Operating Weight50,600 lb
Fuel Capacity119 gal
Cooling System Fluid Capacity17.6 gal
Engine Oil Capacity6.7 gal
Hydraulic Fluid Capacity47 gal
Powertrain Fluid Capacity47 gal
Final Drives Fluid Capacity3.8 gal
Operating Voltage24 V
Alternator Supplied Amperage55 amps
Transmission and speeds
Max Speed - Forward6.8 mph
Max Speed - Reverse6.8 mph
Transmission TypeDual-path, electronic-controlled, closed-loop hydrostatic drive
Number Of Forward Gears3
Number Of Reverse Gears3
Hydraulic System
Relief Valve Pressure2,320 psi
Pump Flow Capacity77 gpm
Pump TypeVariable-displacement piston pump with load-sensing proportional pump flow control
Standard Blade
Blade width13.1 ft
Blade height57 in
Capacity9.5 yd3
Blade Angle (Both Directions)25 degrees
Cutting Depth21 in

Source

950C LGP
SpecificationSource figure
Dimensions and weight
Width Over Tracks9.51 ft
Height To Top Of Cab10.85 ft
Length W/ Blade18.94 ft
Length Of Track On Ground10.75 ft
Ground Clearance1.59 ft
Length W/O Blade14.11 ft
Undercarriage
Track Gauge7.16 ft
Ground Contact Area7,224 in2
Ground Pressure7.42 psi
Standard Shoe Size27.96 in
Number Of Shoes Per Side43
Number Of Track Rollers Per Side8
Track Pitch8.5 in
Engine
Number Of Cylinders6
Engine ModelD 926 TI
Net Power230 hp
Power Measured @1,800 rpm
Max Torque797 lb-ft
Displacement610 cu in
Torque Measured @1,300 rpm
AspirationIntercooled and turbocharged
Operational
Operating Weight54,200 lb
Fuel Capacity119 gal
Cooling System Fluid Capacity17.6 gal
Engine Oil Capacity6.7 gal
Hydraulic Fluid Capacity47 gal
Powertrain Fluid Capacity47 gal
Final Drives Fluid Capacity3.8 gal
Operating Voltage24 V
Alternator Supplied Amperage55 amps
Transmission and speeds
Max Speed - Forward6.8 mph
Max Speed - Reverse6.8 mph
Transmission TypeDual-path, electronic-controlled, closed-loop hydrostatic drive
Number Of Forward Gears3
Number Of Reverse Gears3
Hydraulic System
Relief Valve Pressure2,320 psi
Pump Flow Capacity77 gpm
Pump TypeVariable-displacement piston pump with load-sensing proportional pump flow control
Standard Blade
Blade width14.8 ft
Blade height53 in
Capacity8.2 yd3
Blade Angle (Both Directions)25 degrees
Cutting Depth24 in

Source

950C LT
SpecificationSource figure
Dimensions and weight
Width Over Tracks9.76 ft
Height To Top Of Cab10.85 ft
Length Of Track On Ground10.75 ft
Ground Clearance1.59 ft
Length W/O Blade14.11 ft
Undercarriage
Track Gauge6.5 ft
Ground Contact Area5,160 in2
Ground Pressure10.1 psi
Number Of Shoes Per Side43
Number Of Track Rollers Per Side8
Track Pitch8.5 in
Engine
Number Of Cylinders6
Engine ModelD 926 TI
Net Power230 hp
Power Measured @1,800 rpm
Max Torque797 lb-ft
Displacement610 cu in
Torque Measured @1,300 rpm
AspirationIntercooled and turbocharged
Operational
Operating Weight52,300 lb
Fuel Capacity119 gal
Cooling System Fluid Capacity17.6 gal
Engine Oil Capacity6.7 gal
Hydraulic Fluid Capacity47 gal
Powertrain Fluid Capacity47 gal
Final Drives Fluid Capacity3.8 gal
Operating Voltage24 V
Alternator Supplied Amperage55 amps
Transmission and speeds
Max Speed - Forward6.8 mph
Max Speed - Reverse6.8 mph
Transmission TypeDual-path, electronic-controlled, closed-loop hydrostatic drive
Number Of Forward Gears3
Number Of Reverse Gears3
Hydraulic System
Relief Valve Pressure2,320 psi
Pump Flow Capacity77 gpm
Pump TypeVariable-displacement piston pump with load-sensing proportional pump flow
Standard Blade
Blade width13.1 ft
Blade height57 in
Capacity9.5 yd3
Blade Angle (Both Directions)25 degrees
Cutting Depth21 in

Source

1050C
SpecificationSource figure
Dimensions and weight
Width Over Tracks8.99 ft
Height To Top Of Cab11.95 ft
Length W/ Blade21.05 ft
Length Of Track On Ground10.42 ft
Ground Clearance2.06 ft
Length W/O Blade16.03 ft
Undercarriage
Track Gauge7.16 ft
Ground Contact Area5,510 in2
Ground Pressure13.4 psi
Standard Shoe Size22.05 in
Number Of Shoes Per Side44
Number Of Track Rollers Per Side7
Track Pitch8.5 in
Engine
Number Of Cylinders6
Engine ModelD 9406 TI-E
Net Power324 hp
Power Measured @1,800 rpm
Max Torque1,129 lb-ft
Displacement793 cu in
Torque Measured @1,200 rpm
AspirationIntercooled and turbocharged
Operational
Operating Weight73,985 lb
Fuel Capacity161 gal
Cooling System Fluid Capacity18 gal
Engine Oil Capacity6.3 gal
Hydraulic Fluid Capacity55 gal
Powertrain Fluid Capacity55 gal
Final Drives Fluid Capacity5.5 gal
Operating Voltage24 V
Alternator Supplied Amperage55 amps
Transmission and speeds
Max Speed - Forward6.8 mph
Max Speed - Reverse6.8 mph
Transmission TypeDual-path, electronic-controlled, closed-loop hydrostatic drive
Number Of Forward Gears3
Number Of Reverse Gears3
Hydraulic System
Relief Valve Pressure2,900 psi
Pump Flow Capacity89 gpm
Pump TypeVariable-displacement piston pump with load-sensing proportional pum flow control
Standard Blade
Blade width13.8 ft
Blade height65 in
Capacity12.5 yd3
Cutting Depth22 in

Source

1050C WH
SpecificationSource figure
Dimensions and weight
Width Over Tracks10.32 ft
Height To Top Of Cab11.95 ft
Length Of Track On Ground10.42 ft
Ground Clearance2.06 ft
Length W/O Blade16.03 ft
Undercarriage
Ground Contact Area6,000 in2
Ground Pressure12.9 psi
Number Of Shoes Per Side44
Number Of Track Rollers Per Side7
Track Pitch8.5 in
Engine
Number Of Cylinders6
Engine ModelD 9406 TI-E A3
Net Power324 hp
Power Measured @1,800 rpm
Max Torque1,129 lb-ft
Displacement793 cu in
Torque Measured @1,200 rpm
AspirationIntercooled and turbocharged
Operational
Operating Weight77,445 lb
Fuel Capacity161 gal
Cooling System Fluid Capacity18 gal
Engine Oil Capacity6.3 gal
Hydraulic Fluid Capacity55 gal
Powertrain Fluid Capacity55 gal
Final Drives Fluid Capacity5.5 gal
Operating Voltage24 V
Alternator Supplied Amperage80 amps
Transmission and speeds
Max Speed - Forward6.8 mph
Max Speed - Reverse6.8 mph
Transmission TypeDual-path, electronic-controlled, closed-loop hydrostatic drive
Number Of Forward Gears3
Number Of Reverse Gears3
Hydraulic System
Relief Valve Pressure2,900 psi
Pump Flow Capacity89 gpm
Pump TypeVariable-displacement piston pump with load-sensing proprotional pump flow control
Standard Blade
Blade width13.8 ft
Blade height96.5 in
Capacity27.7 yd3
Blade Angle (Both Directions)25 degrees
Cutting Depth22 in

Source

1050J
SpecificationSource figure
Dimensions and weight
Width Over Tracks9.17 ft
Height To Top Of Cab11.91 ft
Length W/ Blade21.33 ft
Length Of Track On Ground10.42 ft
Ground Clearance2.08 ft
Undercarriage
Track Gauge7.17 ft
Ground Contact Area6,004 in2
Ground Pressure12.9 psi
Standard Shoe Size24 in
Number Of Shoes Per Side44
Number Of Track Rollers Per Side7
Track Pitch8.5 in
Engine
Number Of Cylinders6
Engine ModelD 946-L A6
Net Power335 hp
Power Measured @1,800 rpm
Max Torque1,254 lb-ft
Displacement12.0 L (732 cu in), D946-L A6; original February2014 DKA9501050J [source]
Torque Measured @1,400 rpm
AspirationTurbocharger w/ intercooler
Operational
Operating Weight77,843 lb
Fuel Capacity172 gal
Cooling System Fluid Capacity15 gal
Engine Oil Capacity9 gal
Hydraulic Fluid Capacity55.5 gal
Powertrain Fluid Capacity55.5 gal
Final Drives Fluid Capacity4.9 gal
Operating Voltage24 V
Alternator Supplied Amperage80 amps
Transmission and speeds
Max Speed - Forward6.8 mph
Max Speed - Reverse6.8 mph
Transmission TypeHydrostatic
Hydraulic System
Relief Valve Pressure26,000 kPa (3,770 psi), February2014 GENERAL1050J brochure; earlier dedicated waste-handler brochure prints3,700psi withsame26,000kPa, different publication entry retained [source]
Pump Flow Capacity68 gpm
Pump TypeVariable axial-piston
Standard Blade
Blade width13.3 ft
Blade height65 in
Capacity11.6 yd3
Cutting Depth22 in

Source

1050J Waste Handler
SpecificationSource figure
Dimensions and weight
Width Over Tracks9.17 ft
Height To Top Of Cab11.91 ft
Length W/ Blade21.33 ft
Length Of Track On Ground10.42 ft
Ground Clearance2.08 ft
Undercarriage
Track Gauge7.17 ft
Ground Contact Area6,004 in2
Ground Pressure13.8 psi
Standard Shoe Size24 in
Number Of Shoes Per Side44
Number Of Track Rollers Per Side7
Track Pitch8.5 in
Engine
Number Of Cylinders6
Engine ModelD 946-L A6
Net Power335 hp
Power Measured @1,800 rpm
Max Torque1,254 lb-ft
Displacement12.0 L (732 cu in), D946-L A6; dedicated Deere Waste Handler brochure [source]
Torque Measured @1,400 rpm
AspirationTurbocharger w/ intercooler
Operational
Operating Weight80,967 lb
Fuel Capacity171.7 gal
Cooling System Fluid Capacity15.1 gal
Engine Oil Capacity9 gal
Hydraulic Fluid Capacity55.5 gal
Powertrain Fluid Capacity55.5 gal
Final Drives Fluid Capacity4.9 gal
Operating Voltage24 V
Alternator Supplied Amperage80 amps
Transmission and speeds
Max Speed - Forward6.8 mph
Max Speed - Reverse6.8 mph
Transmission TypeHydrostatic
Hydraulic System
Relief Valve Pressure3,700 psi
Pump Flow Capacity68 gpm
Pump TypeVariable axial-piston
Standard Blade
Blade width13.3 ft
Blade height94 in
Capacity25.8 yd3
Cutting Depth22 in
Additional specifications
Dedicated Waste Package And Weight ScopeDedicatedWHbrochure:semiU/rack,24in610mmextreme-serviceshoeswithtrapezoidalholes/fullfuel/operator for80967lb36726kg;shipping20percentfuelwithoutblade/attachments. Perforatedshields/cabbarrier/hoseguards separateoptionalstrikerbars andpoweredcabprecleaner. [source]
Waste Handler Seal And Fan ArrangementBolt-onfinaldrivesealguard,outeroil-filleddoubleseal/cabwarningbeforeinnerfinaldriveoilloss; separateengineandhydraulicfans/reversers. GeneralFebruary2014Jbrochurelistsreversersasoption;do notassumeeveryJstandarddozerhaswastepackage. [source]

Source

Compare John Deere 950C, 950C LGP, 950C LT, 1050C, 1050C WH, 1050J, 1050J Waste Handler
Dimensions and weight
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Width Over Tracks8.17 ft9.51 ft9.76 ft8.99 ft10.32 ft9.17 ft9.17 ft
Height To Top Of Cab10.85 ft10.85 ft10.85 ft11.95 ft11.95 ft11.91 ft11.91 ft
Length Of Track On Ground9.72 ft10.75 ft10.75 ft10.42 ft10.42 ft10.42 ft10.42 ft
Ground Clearance1.59 ft1.59 ft1.59 ft2.06 ft2.06 ft2.08 ft2.08 ft
Undercarriage
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Number Of Shoes Per Side39434344444444
Ground Pressure10.81 psi7.42 psi10.1 psi13.4 psi12.9 psi12.9 psi13.8 psi
Ground Contact Area4,680 in27,224 in25,160 in25,510 in26,000 in26,004 in26,004 in2
Number Of Track Rollers Per Side7887777
Track Pitch8.5 in8.5 in8.5 in8.5 in8.5 in8.5 in8.5 in
Engine
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Number Of Cylinders6666666
Engine ModelD926 TID 926 TID 926 TID 9406 TI-ED 9406 TI-E A3D 946-L A6D 946-L A6
Net Power230 hp230 hp230 hp324 hp324 hp335 hp335 hp
Power Measured @1,800 rpm1,800 rpm1,800 rpm1,800 rpm1,800 rpm1,800 rpm1,800 rpm
Max Torque797 lb-ft797 lb-ft797 lb-ft1,129 lb-ft1,129 lb-ft1,254 lb-ft1,254 lb-ft
Displacement610 cu in610 cu in610 cu in793 cu in793 cu in12.0 L (732 cu in), D946-L A6; original February2014 DKA9501050J [source]12.0 L (732 cu in), D946-L A6; dedicated Deere Waste Handler brochure [source]
Torque Measured @1,300 rpm1,300 rpm1,300 rpm1,200 rpm1,200 rpm1,400 rpm1,400 rpm
AspirationIntercooled and turbochargedIntercooled and turbochargedIntercooled and turbochargedIntercooled and turbochargedIntercooled and turbochargedTurbocharger w/ intercoolerTurbocharger w/ intercooler
Operational
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Operating Weight50,600 lb54,200 lb52,300 lb73,985 lb77,445 lb77,843 lb80,967 lb
Fuel Capacity119 gal119 gal119 gal161 gal161 gal172 gal171.7 gal
Cooling System Fluid Capacity17.6 gal17.6 gal17.6 gal18 gal18 gal15 gal15.1 gal
Engine Oil Capacity6.7 gal6.7 gal6.7 gal6.3 gal6.3 gal9 gal9 gal
Hydraulic Fluid Capacity47 gal47 gal47 gal55 gal55 gal55.5 gal55.5 gal
Powertrain Fluid Capacity47 gal47 gal47 gal55 gal55 gal55.5 gal55.5 gal
Final Drives Fluid Capacity3.8 gal3.8 gal3.8 gal5.5 gal5.5 gal4.9 gal4.9 gal
Operating Voltage24 V24 V24 V24 V24 V24 V24 V
Alternator Supplied Amperage55 amps55 amps55 amps55 amps80 amps80 amps80 amps
Transmission and speeds
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Transmission TypeDual-path, electronic-controlled, closed-loop hydrostatic driveDual-path, electronic-controlled, closed-loop hydrostatic driveDual-path, electronic-controlled, closed-loop hydrostatic driveDual-path, electronic-controlled, closed-loop hydrostatic driveDual-path, electronic-controlled, closed-loop hydrostatic driveHydrostaticHydrostatic
Max Speed - Forward6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph
Max Speed - Reverse6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph6.8 mph
Hydraulic System
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Pump TypeVariable-displacement piston pump with load-sensing proportional pump flow controlVariable-displacement piston pump with load-sensing proportional pump flow controlVariable-displacement piston pump with load-sensing proportional pump flowVariable-displacement piston pump with load-sensing proportional pum flow controlVariable-displacement piston pump with load-sensing proprotional pump flow controlVariable axial-pistonVariable axial-piston
Relief Valve Pressure2,320 psi2,320 psi2,320 psi2,900 psi2,900 psi26,000 kPa (3,770 psi), February2014 GENERAL1050J brochure; earlier dedicated waste-handler brochure prints3,700psi withsame26,000kPa, different publication entry retained [source]3,700 psi
Pump Flow Capacity77 gpm77 gpm77 gpm89 gpm89 gpm68 gpm68 gpm
Standard Blade
Specification950C950C LGP950C LT1050C1050C WH1050J1050J Waste Handler
Blade width13.1 ft14.8 ft13.1 ft13.8 ft13.8 ft13.3 ft13.3 ft
Blade height57 in53 in57 in65 in96.5 in65 in94 in
Capacity9.5 yd38.2 yd39.5 yd312.5 yd327.7 yd311.6 yd325.8 yd3
Cutting Depth21 in24 in21 in22 in22 in22 in22 in

More in John Deere: 950J/950J LGP/950J Waste Handler specs, 764HSD, 850/850 X-Tier E-Drive specs.