Machine models
Zoomlion QY30V431–QY50V532: boom mechanisms and carrier controls
What the QY50V532 boom diagram actually describes
Zoomlion's May 2012 training book divides this main boom into a base section and four sliding sections. A separate derricking cylinder changes the boom angle. The telescope cylinders extend the nested sections; they do not perform the derricking function.
This distinction helps identify which movement a seller means when reporting a boom problem.
The illustrated telescope mechanism combines two cylinders with wire ropes. Its first cylinder moves the first sliding section and carries the remaining sections with it. The second cylinder and rope arrangement coordinate the other sliding sections.
A description such as “hydraulic boom” leaves out that mechanical connection. The book also identifies welded upper and lower parts forming the U-shaped boom body.
The jib is another assembly, combining a lattice section with a rectangular telescoping section. The rooster sheave serves single-line hoisting at the boom head. It does not give that single line the crane's full multi-part lifting capacity.
Match the actual boom and reeving to the operating chart before planning a lift.
Source: Zoomlion QY50V532 Boom Structure and Installation, Version 01, May 2012.
QY50V532 carrier instruments and hydraulic equipment
The original sales booklet describes a four-axle carrier, not a three-axle truck. Its technical table labels the turning measurement as a diameter. Treating the same number as a radius would double the space implied by the published figure.
The booklet also separates maximum main-boom height from the height with a jib installed.
For servicing access, the engine hood's side door opens upward toward the electrical equipment. The hydraulic specification describes a change from three pumps to four and a filter-condition warning at the oil tank. Those details identify this V532 arrangement more closely than an unqualified comparison of rated tonnage.
Source: Original Zoomlion QY50V532 sales booklet, chassis, hydraulic equipment and technical parameters.
Che Xia's May 2011 chassis-electrical training explains the two needles in the air-pressure gauge: one monitors the front reservoir circuit, the other the intermediate and rear circuit. The low-air warning must clear at the prescribed pressure before driving. A separate parking-brake lamp concerns the applied parking brake.
Neither should be confused with the PTO indicator, which reports the power take-off selection.
The training also marks emergency steering and the fifth-outrigger retraction indicator as optional equipment. An unused lamp position therefore does not prove that its associated system is installed. Read the fitted controls and machine documentation together when identifying the carrier.
Source: Zoomlion QY50V532 Crane Chassis Electrics, Che Xia, May 10, 2011.
| Model and field | Earlier entry | Manufacturer figure and scope | Source |
|---|
| Listing-entry count |
|---|
| 7 |
Zoomlion QY30V431–QY50V532: boom mechanisms and carrier controls: hydraulic truck cranes.
| Configuration | Documented field and quantity |
|---|---|
| QY30V431 |
|
| QY30V521 |
|
| QY30V531 |
|
| QY40V521 |
|
| QY40V531 |
|
| QY50V522 |
|
| QY50V532 |
|
| Publisher name | Source guide | Listing-entry count | Labels named by the source |
|---|---|---|---|
| Zoomlion | QY30V431 to QY50V532 | 7 | QY30V431, QY30V521, QY30V531, QY40V521, QY40V531, QY50V522, and 1 more |
| Specification | QY30V431 | QY30V521 | QY30V531 | QY40V521 | QY40V531 | QY50V522 | QY50V532 |
|---|---|---|---|---|---|---|---|
| Min Height @ Max Raise Angle | 37.08 ft | 36.42 ft | 36.42 ft | 38.39 ft | 38.39 ft | 38.06 ft | 38.06 ft |
| Max Height @ Max Raise Angle - No Jib | 113.52 ft | 132.88 ft | 132.88 ft | 133.21 ft | 133.21 ft | 138.13 ft | 138.13 ft |
| Min Working Radius | 9.85 ft | 9.85 ft | 9.85 ft | 9.85 ft | 9.85 ft | 9.85 ft | 9.85 ft |
| Max Working Radius | 91.87 ft | 104.99 ft | 104.99 ft | 98.43 ft | 98.43 ft | 104.99 ft | 104.99 ft |
| Max Elevating Angle | 80 degrees | 80 degrees | 80 degrees | 80 degrees | 80 degrees | 80 degrees | 80 degrees |
| Max Lift Capacity | 70,548 lb | 70,548 lb | 70,548 lb | 88,185 lb | 88,185 lb | 121,254 lb | 121,254 lb |
| Number Of Sections | 4+jib | 5 | 5 | 5 + 2 jibs | 5 + 2 jibs | 5 | 5 |
| Specification | QY30V431 | QY30V521 | QY30V531 | QY40V521 | QY40V531 | QY50V522 | QY50V532 |
|---|---|---|---|---|---|---|---|
| Transport Length | 42.33 ft | 42.66 ft | 42.66 ft | 42.33 ft | 42.33 ft | 43.64 ft | 43.64 ft |
| Transport Width | 8.21 ft | 8.21 ft | 8.21 ft | 9.03 ft | 9.03 ft | 9.03 ft | 9.03 ft |
| Transport Height | 11.16 ft | 11.16 ft | 11.16 ft | 12.01 ft | 12.01 ft | 11.98 ft | 11.98 ft |
| Ground Clearance | 0.73 ft | 0.73 ft | 0.73 ft | 0.94 ft | 0.94 ft | 0.86 ft | 0.86 ft |
| Width W/ Outriggers Extended | 20.02 ft | 20.02 ft | 20.02 ft | 21.66 ft | 21.66 ft | 22.64 ft | 22.64 ft |
| Carrier Length | 35.29 ft | 35.29 ft | 35.29 ft | 36.89 ft | 36.89 ft | 38.06 ft | 38.06 ft |
| Specification | QY30V431 | QY30V521 | QY30V531 | QY40V521 | QY40V531 | QY50V522 | QY50V532 |
|---|---|---|---|---|---|---|---|
| Model | WP10.270 | WD615.50 | WP10.270 | WD615.44 | WP10.336 | WD615.44 | ZLJ5414 |
| Gross Power | 266.9 hp | 276.3 hp | 266.9 hp | 325.9 hp | 331.3 hp | 325.9 hp | 331.3 hp |
| Power Measured @ | 2,200 rpm | 2,200 rpm | 2,200 rpm | 2,200 rpm | 2,200 rpm | 2,200 rpm | 2,200 rpm |
| Max Torque | 811.4 lb-ft | 922 lb-ft | 811.4 lb-ft | 922 lb-ft | 922 lb-ft | 922 lb-ft | 922 lb-ft |
| Torque Measured @ | 1,600 rpm | 1,600 rpm | 1,600 rpm | 1,600 rpm | 1,600 rpm | 1,600 rpm | 1,600 rpm |
| Specification | QY30V431 | QY30V521 | QY30V531 | QY40V521 | QY40V531 | QY50V522 | QY50V532 |
|---|---|---|---|---|---|---|---|
| Operating Weight | 64,816 lb | 69,887 lb | 69,887 lb | 81,064 lb | 81,064 lb | 89,221 lb | 89,221 lb |
| Number Of Axels | 3 | 3 | 3 | 4 | 4 | 4 | 4 |
| Source guide | Differing-field count reported |
|---|---|
| QY30V431 to QY50V532 | 16 |
| Figure | QY30V431 | QY30V521 | QY30V531 | QY40V521 | QY40V531 | QY50V522 | QY50V532 |
|---|---|---|---|---|---|---|---|
| Engine horsepower per 1,000 lb of weight | 4.1 | 4.0 | 3.8 | 4.0 | 4.1 | 3.7 | 3.7 |
Zoomlion QY30V431–QY50V532: boom mechanisms and carrier controls: hydraulic truck crane
History and service record of QY30V431 to QY50V532
The sourced history for this model line, such as “Company founding and listing”, is on the QY100H-3 page; it is not repeated here.
| Observation date | Listing source | Equipment search | Listings |
|---|---|---|---|
| 2026-09-24 | MachineryTrader | Zoomlion hydraulic truck crane | 1 |
| Model | Listed | Model years | Lowest asking | Highest asking | Median asking | Median hours |
|---|---|---|---|---|---|---|
| QY50V532 | 1 | 2012 | $105,000 | $105,000 | $105,000 | None shown |
| Search date | Database | Names queried | Search result |
|---|---|---|---|
| 2026-09-24 | U.S. Consumer Product Safety Commission | Zoomlion together with the hydraulic truck crane QY30V431, QY30V521, QY30V531, QY40V521 | No matching recall in this search |
| Evidence class | Document, classification and recorded date |
|---|---|
| Reference site |
|
| Reference site |
|
| Reference site |
|
| Reference site |
|
| Reference site |
|
| Reference site |
|
| Reference site |
|
| Used-market listings |
|
| Federal agency data |
|
Zoomlion QY30V431–QY50V532: boom mechanisms and carrier controls: Configuration records
QY30V431
| Specification | Source figure |
|---|---|
| Boom | |
| Min Height @ Max Raise Angle | 37.08 ft |
| Max Height @ Max Raise Angle - No Jib | 113.52 ft |
| Min Working Radius | 9.85 ft |
| Max Working Radius | 91.87 ft |
| Max Elevating Angle | 80 degrees |
| Max Lift Capacity | 70,548 lb |
| Number Of Sections | 4+jib |
| Dimensions and weight | |
| Transport Length | 42.33 ft |
| Transport Width | 8.21 ft |
| Transport Height | 11.16 ft |
| Ground Clearance | 0.73 ft |
| Width W/ Outriggers Extended | 20.02 ft |
| Carrier Length | 35.29 ft |
| Carrier Engine | |
| Model | WP10.270 |
| Gross Power | 266.9 hp |
| Power Measured @ | 2,200 rpm |
| Max Torque | 811.4 lb-ft |
| Torque Measured @ | 1,600 rpm |
| Operational | |
| Operating Weight | 64,816 lb |
| Number Of Axels | 3 |
QY30V521
| Specification | Source figure |
|---|---|
| Boom | |
| Min Height @ Max Raise Angle | 36.42 ft |
| Max Height @ Max Raise Angle - No Jib | 132.88 ft |
| Min Working Radius | 9.85 ft |
| Max Working Radius | 104.99 ft |
| Max Elevating Angle | 80 degrees |
| Max Lift Capacity | 70,548 lb |
| Number Of Sections | 5 |
| Dimensions and weight | |
| Transport Length | 42.66 ft |
| Transport Width | 8.21 ft |
| Transport Height | 11.16 ft |
| Ground Clearance | 0.73 ft |
| Width W/ Outriggers Extended | 20.02 ft |
| Carrier Length | 35.29 ft |
| Carrier Engine | |
| Model | WD615.50 |
| Gross Power | 276.3 hp |
| Power Measured @ | 2,200 rpm |
| Max Torque | 922 lb-ft |
| Torque Measured @ | 1,600 rpm |
| Operational | |
| Operating Weight | 69,887 lb |
| Number Of Axels | 3 |
QY30V531
| Specification | Source figure |
|---|---|
| Boom | |
| Min Height @ Max Raise Angle | 36.42 ft |
| Max Height @ Max Raise Angle - No Jib | 132.88 ft |
| Min Working Radius | 9.85 ft |
| Max Working Radius | 104.99 ft |
| Max Elevating Angle | 80 degrees |
| Max Lift Capacity | 70,548 lb |
| Number Of Sections | 5 |
| Dimensions and weight | |
| Transport Length | 42.66 ft |
| Transport Width | 8.21 ft |
| Transport Height | 11.16 ft |
| Ground Clearance | 0.73 ft |
| Width W/ Outriggers Extended | 20.02 ft |
| Carrier Length | 35.29 ft |
| Carrier Engine | |
| Model | WP10.270 |
| Gross Power | 266.9 hp |
| Power Measured @ | 2,200 rpm |
| Max Torque | 811.4 lb-ft |
| Torque Measured @ | 1,600 rpm |
| Operational | |
| Operating Weight | 69,887 lb |
| Number Of Axels | 3 |
QY40V521
| Specification | Source figure |
|---|---|
| Boom | |
| Min Height @ Max Raise Angle | 38.39 ft |
| Max Height @ Max Raise Angle - No Jib | 133.21 ft |
| Min Working Radius | 9.85 ft |
| Max Working Radius | 98.43 ft |
| Max Elevating Angle | 80 degrees |
| Max Lift Capacity | 88,185 lb |
| Number Of Sections | 5 + 2 jibs |
| Dimensions and weight | |
| Transport Length | 42.33 ft |
| Transport Width | 9.03 ft |
| Transport Height | 12.01 ft |
| Ground Clearance | 0.94 ft |
| Width W/ Outriggers Extended | 21.66 ft |
| Carrier Length | 36.89 ft |
| Carrier Engine | |
| Model | WD615.44 |
| Gross Power | 325.9 hp |
| Power Measured @ | 2,200 rpm |
| Max Torque | 922 lb-ft |
| Torque Measured @ | 1,600 rpm |
| Operational | |
| Operating Weight | 81,064 lb |
| Number Of Axels | 4 |
QY40V531
| Specification | Source figure |
|---|---|
| Boom | |
| Min Height @ Max Raise Angle | 38.39 ft |
| Max Height @ Max Raise Angle - No Jib | 133.21 ft |
| Min Working Radius | 9.85 ft |
| Max Working Radius | 98.43 ft |
| Max Elevating Angle | 80 degrees |
| Max Lift Capacity | 88,185 lb |
| Number Of Sections | 5 + 2 jibs |
| Dimensions and weight | |
| Transport Length | 42.33 ft |
| Transport Width | 9.03 ft |
| Transport Height | 12.01 ft |
| Ground Clearance | 0.94 ft |
| Width W/ Outriggers Extended | 21.66 ft |
| Carrier Length | 36.89 ft |
| Carrier Engine | |
| Model | WP10.336 |
| Gross Power | 331.3 hp |
| Power Measured @ | 2,200 rpm |
| Max Torque | 922 lb-ft |
| Torque Measured @ | 1,600 rpm |
| Operational | |
| Operating Weight | 81,064 lb |
| Number Of Axels | 4 |
QY50V522
| Specification | Source figure |
|---|---|
| Boom | |
| Min Height @ Max Raise Angle | 38.06 ft |
| Max Height @ Max Raise Angle - No Jib | 138.13 ft |
| Min Working Radius | 9.85 ft |
| Max Working Radius | 104.99 ft |
| Max Elevating Angle | 80 degrees |
| Max Lift Capacity | 121,254 lb |
| Number Of Sections | 5 |
| Dimensions and weight | |
| Transport Length | 43.64 ft |
| Transport Width | 9.03 ft |
| Transport Height | 11.98 ft |
| Ground Clearance | 0.86 ft |
| Width W/ Outriggers Extended | 22.64 ft |
| Carrier Length | 38.06 ft |
| Carrier Engine | |
| Model | WD615.44 |
| Gross Power | 325.9 hp |
| Power Measured @ | 2,200 rpm |
| Max Torque | 922 lb-ft |
| Torque Measured @ | 1,600 rpm |
| Operational | |
| Operating Weight | 89,221 lb |
| Number Of Axels | 4 |
QY50V532
| Specification | Source figure |
|---|---|
| Boom | |
| Min Height @ Max Raise Angle | 38.06 ft |
| Max Height @ Max Raise Angle - No Jib | 138.13 ft |
| Min Working Radius | 9.85 ft |
| Max Working Radius | 104.99 ft |
| Max Elevating Angle | 80 degrees |
| Max Lift Capacity | 121,254 lb |
| Number Of Sections | 5 |
| Dimensions and weight | |
| Transport Length | 43.64 ft |
| Transport Width | 9.03 ft |
| Transport Height | 11.98 ft |
| Ground Clearance | 0.86 ft |
| Width W/ Outriggers Extended | 22.64 ft |
| Carrier Length | 38.06 ft |
| Carrier Engine | |
| Model | ZLJ5414 |
| Gross Power | 331.3 hp |
| Power Measured @ | 2,200 rpm |
| Max Torque | 922 lb-ft |
| Torque Measured @ | 1,600 rpm |
| Operational | |
| Operating Weight | 89,221 lb |
| Number Of Axels | 4 |
| Additional specifications | |
| Original Boom And Chassis Scope | May2012 training: base boom plus four telescopic sections; two telescoping cylinders with ropes, separate derricking cylinder; lattice plus rectangular telescoping jib, single-line rooster sheave. Original sales booklet describes four-axle chassis and marks turning measurement as diameter. [source] [source] |
More in Zoomlion: YZ rollers: drums/drive/engine identities, BG2000D/BG2100C, QY100H-3.